1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright (C) 2010 Andreas Biemann <biessmann.devel (at) googlemail.com> 4 * 5 * based on previous work by 6 * 7 * Ulf Samuelsson <ulf (at) atmel.com> 8 * Rick Bronson <rick (at) efn.org> 9 * 10 * Configuration settings for the AT91RM9200EK board. 11 */ 12 13 #ifndef __AT91RM9200EK_CONFIG_H__ 14 #define __AT91RM9200EK_CONFIG_H__ 15 16 #include <linux/sizes.h> 17 18 /* 19 * set some initial configurations depending on configure target 20 * 21 * at91rm9200ek_config -> boot from 0x0 in NOR Flash at CS0 22 * at91rm9200ek_ram_config -> continue booting from 0x20100000 in RAM; lowlevel 23 * initialisation was done by some preloader 24 */ 25 #ifdef CONFIG_RAMBOOT 26 #define CONFIG_SKIP_LOWLEVEL_INIT 27 #endif 28 29 /* 30 * AT91C_XTAL_CLOCK is the frequency of external xtal in hertz 31 * AT91C_MAIN_CLOCK is the frequency of PLLA output 32 * AT91C_MASTER_CLOCK is the peripherial clock 33 * CONFIG_SYS_HZ_CLOCK is the value for CCR in tc0 (divider 2 is implicitely 34 * set in arch/arm/cpu/arm920t/at91/timer.c) 35 * CONFIG_SYS_HZ is the tick rate for timer tc0 36 */ 37 #define AT91C_XTAL_CLOCK 18432000 38 #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 39 #define AT91C_MAIN_CLOCK ((AT91C_XTAL_CLOCK / 4) * 39) 40 #define AT91C_MASTER_CLOCK (AT91C_MAIN_CLOCK / 3 ) 41 #define CONFIG_SYS_HZ_CLOCK (AT91C_MASTER_CLOCK / 2) 42 43 /* CPU configuration */ 44 #define CONFIG_AT91RM9200 45 #define CONFIG_AT91RM9200EK 46 #define USE_920T_MMU 47 48 #include <asm/hardware.h> /* needed for port definitions */ 49 50 #define CONFIG_CMDLINE_TAG 51 #define CONFIG_SETUP_MEMORY_TAGS 52 #define CONFIG_INITRD_TAG 53 54 /* 55 * Memory Configuration 56 */ 57 #define CONFIG_NR_DRAM_BANKS 1 58 #define CONFIG_SYS_SDRAM_BASE 0x20000000 59 #define CONFIG_SYS_SDRAM_SIZE SZ_32M 60 61 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE 62 #define CONFIG_SYS_MEMTEST_END \ 63 (CONFIG_SYS_MEMTEST_START + CONFIG_SYS_SDRAM_SIZE - SZ_256K) 64 65 /* 66 * LowLevel Init 67 */ 68 #ifndef CONFIG_SKIP_LOWLEVEL_INIT 69 #define CONFIG_SYS_USE_MAIN_OSCILLATOR 70 /* flash */ 71 #define CONFIG_SYS_EBI_CFGR_VAL 0x00000000 72 #define CONFIG_SYS_SMC_CSR0_VAL 0x00003284 /* 16bit, 2 TDF, 4 WS */ 73 74 /* clocks */ 75 #define CONFIG_SYS_PLLAR_VAL 0x20263E04 /* 179.712000 MHz for PCK */ 76 #define CONFIG_SYS_PLLBR_VAL 0x10483E0E /* 48.054857 MHz (divider by 2 for USB) */ 77 /* PCK/3 = MCK Master Clock = 59.904000MHz from PLLA */ 78 #define CONFIG_SYS_MCKR_VAL 0x00000202 79 80 /* sdram */ 81 #define CONFIG_SYS_PIOC_ASR_VAL 0xFFFF0000 /* Configure PIOC as peripheral (D16/D31) */ 82 #define CONFIG_SYS_PIOC_BSR_VAL 0x00000000 83 #define CONFIG_SYS_PIOC_PDR_VAL 0xFFFF0000 84 #define CONFIG_SYS_EBI_CSA_VAL 0x00000002 /* CS1=CONFIG_SYS_SDRAM */ 85 #define CONFIG_SYS_SDRC_CR_VAL 0x2188c155 /* set up the CONFIG_SYS_SDRAM */ 86 #define CONFIG_SYS_SDRAM CONFIG_SYS_SDRAM_BASE /* address of the SDRAM */ 87 #define CONFIG_SYS_SDRAM1 (CONFIG_SYS_SDRAM_BASE+0x80) 88 #define CONFIG_SYS_SDRAM_VAL 0x00000000 /* value written to CONFIG_SYS_SDRAM */ 89 #define CONFIG_SYS_SDRC_MR_VAL 0x00000002 /* Precharge All */ 90 #define CONFIG_SYS_SDRC_MR_VAL1 0x00000004 /* refresh */ 91 #define CONFIG_SYS_SDRC_MR_VAL2 0x00000003 /* Load Mode Register */ 92 #define CONFIG_SYS_SDRC_MR_VAL3 0x00000000 /* Normal Mode */ 93 #define CONFIG_SYS_SDRC_TR_VAL 0x000002E0 /* Write refresh rate */ 94 #endif /* CONFIG_SKIP_LOWLEVEL_INIT */ 95 96 /* 97 * Hardware drivers 98 */ 99 /* 100 * Choose a USART for serial console 101 * CONFIG_DBGU is DBGU unit on J10 102 * CONFIG_USART1 is USART1 on J14 103 */ 104 #define CONFIG_ATMEL_USART 105 #define CONFIG_USART_BASE ATMEL_BASE_DBGU 106 #define CONFIG_USART_ID 0/* ignored in arm */ 107 108 /* 109 * Command line configuration. 110 */ 111 112 /* 113 * Network Driver Setting 114 */ 115 #define CONFIG_DRIVER_AT91EMAC 116 #define CONFIG_SYS_RX_ETH_BUFFER 16 117 #define CONFIG_RMII 118 #define CONFIG_MII 119 120 /* 121 * NOR Flash 122 */ 123 #define CONFIG_FLASH_CFI_DRIVER 124 #define CONFIG_SYS_FLASH_CFI 125 #define CONFIG_SYS_FLASH_BASE 0x10000000 126 #define PHYS_FLASH_1 CONFIG_SYS_FLASH_BASE 127 #define PHYS_FLASH_SIZE SZ_8M 128 #define CONFIG_SYS_MAX_FLASH_BANKS 1 129 #define CONFIG_SYS_MAX_FLASH_SECT 256 130 #define CONFIG_SYS_FLASH_PROTECTION 131 132 /* 133 * USB Config 134 */ 135 #define CONFIG_USB_ATMEL 1 136 #define CONFIG_USB_ATMEL_CLK_SEL_PLLB 137 #define CONFIG_USB_OHCI_NEW 1 138 139 #define CONFIG_SYS_USB_OHCI_CPU_INIT 1 140 #define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_USB_HOST_BASE 141 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91rm9200" 142 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 143 144 /* 145 * Environment Settings 146 */ 147 148 /* 149 * after u-boot.bin 150 */ 151 #define CONFIG_ENV_ADDR \ 152 (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN) 153 #define CONFIG_ENV_SIZE SZ_64K /* sectors are 64K here */ 154 /* The following #defines are needed to get flash environment right */ 155 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE 156 #define CONFIG_SYS_MONITOR_LEN SZ_256K 157 158 /* 159 * Boot option 160 */ 161 162 /* default load address */ 163 #define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE + SZ_16M 164 #define CONFIG_ENV_OVERWRITE 165 166 /* 167 * Shell Settings 168 */ 169 170 /* 171 * Size of malloc() pool 172 */ 173 #define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + SZ_128K, \ 174 SZ_4K) 175 176 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_4K \ 177 - GENERATED_GBL_DATA_SIZE) 178 179 #endif /* __AT91RM9200EK_CONFIG_H__ */ 180
