1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * esd vme8349 U-Boot configuration file 4 * Copyright (c) 2008, 2009 esd gmbh Hannover Germany 5 * 6 * (C) Copyright 2006-2010 7 * Wolfgang Denk, DENX Software Engineering, wd (at) denx.de. 8 * 9 * reinhard.arlt (at) esd-electronics.de 10 * Based on the MPC8349EMDS config. 11 */ 12 13 /* 14 * vme8349 board configuration file. 15 */ 16 17 #ifndef __CONFIG_H 18 #define __CONFIG_H 19 20 /* 21 * Top level Makefile configuration choices 22 */ 23 #ifdef CONFIG_CADDY2 24 #define VME_CADDY2 25 #endif 26 27 /* 28 * High Level Configuration Options 29 */ 30 #define CONFIG_E300 1 /* E300 Family */ 31 #define CONFIG_MPC834x 1 /* MPC834x family */ 32 #define CONFIG_MPC8349 1 /* MPC8349 specific */ 33 #define CONFIG_VME8349 1 /* ESD VME8349 board specific */ 34 35 #define CONFIG_MISC_INIT_R 36 37 /* Don't enable PCI2 on vme834x - it doesn't exist physically. */ 38 #undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */ 39 40 #define CONFIG_PCI_66M 41 #ifdef CONFIG_PCI_66M 42 #define CONFIG_83XX_CLKIN 66000000 /* in Hz */ 43 #else 44 #define CONFIG_83XX_CLKIN 33000000 /* in Hz */ 45 #endif 46 47 #ifndef CONFIG_SYS_CLK_FREQ 48 #ifdef CONFIG_PCI_66M 49 #define CONFIG_SYS_CLK_FREQ 66000000 50 #define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_4X1 51 #else 52 #define CONFIG_SYS_CLK_FREQ 33000000 53 #define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_8X1 54 #endif 55 #endif 56 57 #define CONFIG_SYS_IMMR 0xE0000000 58 59 #undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */ 60 #define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */ 61 #define CONFIG_SYS_MEMTEST_END 0x00100000 62 63 /* 64 * DDR Setup 65 */ 66 #define CONFIG_DDR_ECC /* only for ECC DDR module */ 67 #define CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */ 68 #define CONFIG_SPD_EEPROM 69 #define SPD_EEPROM_ADDRESS 0x54 70 #define CONFIG_SYS_READ_SPD vme8349_read_spd 71 #define CONFIG_SYS_83XX_DDR_USES_CS0 /* esd; Fsl board uses CS2/CS3 */ 72 73 /* 74 * 32-bit data path mode. 75 * 76 * Please note that using this mode for devices with the real density of 64-bit 77 * effectively reduces the amount of available memory due to the effect of 78 * wrapping around while translating address to row/columns, for example in the 79 * 256MB module the upper 128MB get aliased with contents of the lower 80 * 128MB); normally this define should be used for devices with real 32-bit 81 * data path. 82 */ 83 #undef CONFIG_DDR_32BIT 84 85 #define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is sys memory*/ 86 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE 87 #define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE 88 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \ 89 | DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075) 90 #define CONFIG_DDR_2T_TIMING 91 #define CONFIG_SYS_DDRCDR (DDRCDR_DHC_EN \ 92 | DDRCDR_ODT \ 93 | DDRCDR_Q_DRN) 94 /* 0x80080001 */ 95 96 /* 97 * FLASH on the Local Bus 98 */ 99 #define CONFIG_SYS_FLASH_CFI 100 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */ 101 #ifdef VME_CADDY2 102 #define CONFIG_SYS_FLASH_BASE 0xffc00000 /* start of FLASH */ 103 #define CONFIG_SYS_FLASH_SIZE 4 /* flash size in MB */ 104 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ 105 BR_PS_16 | /* 16bit */ \ 106 BR_MS_GPCM | /* MSEL = GPCM */ \ 107 BR_V) /* valid */ 108 109 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ 110 | OR_GPCM_XAM \ 111 | OR_GPCM_CSNT \ 112 | OR_GPCM_ACS_DIV2 \ 113 | OR_GPCM_XACS \ 114 | OR_GPCM_SCY_15 \ 115 | OR_GPCM_TRLX_SET \ 116 | OR_GPCM_EHTR_SET \ 117 | OR_GPCM_EAD) 118 /* 0xffc06ff7 */ 119 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 120 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_4MB) 121 #else 122 #define CONFIG_SYS_FLASH_BASE 0xf8000000 /* start of FLASH */ 123 #define CONFIG_SYS_FLASH_SIZE 128 /* flash size in MB */ 124 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ 125 BR_PS_16 | /* 16bit */ \ 126 BR_MS_GPCM | /* MSEL = GPCM */ \ 127 BR_V) /* valid */ 128 129 #define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \ 130 | OR_GPCM_XAM \ 131 | OR_GPCM_CSNT \ 132 | OR_GPCM_ACS_DIV2 \ 133 | OR_GPCM_XACS \ 134 | OR_GPCM_SCY_15 \ 135 | OR_GPCM_TRLX_SET \ 136 | OR_GPCM_EHTR_SET \ 137 | OR_GPCM_EAD) 138 /* 0xf8006ff7 */ 139 #define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE 140 #define CONFIG_SYS_LBLAWAR0_PRELIM (LBLAWAR_EN | LBLAWAR_128MB) 141 #endif 142 /* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */ 143 144 #define CONFIG_SYS_WINDOW1_BASE 0xf0000000 145 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_WINDOW1_BASE \ 146 | BR_PS_32 \ 147 | BR_MS_GPCM \ 148 | BR_V) 149 /* 0xF0001801 */ 150 #define CONFIG_SYS_OR1_PRELIM (OR_AM_256KB \ 151 | OR_GPCM_SETA) 152 /* 0xfffc0208 */ 153 #define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_WINDOW1_BASE 154 #define CONFIG_SYS_LBLAWAR1_PRELIM (LBLAWAR_EN | LBLAWAR_256KB) 155 156 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 157 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device*/ 158 159 #undef CONFIG_SYS_FLASH_CHECKSUM 160 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase TO (ms) */ 161 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write TO (ms) */ 162 163 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 164 165 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) 166 #define CONFIG_SYS_RAMBOOT 167 #else 168 #undef CONFIG_SYS_RAMBOOT 169 #endif 170 171 #define CONFIG_SYS_INIT_RAM_LOCK 1 172 #define CONFIG_SYS_INIT_RAM_ADDR 0xF7000000 /* Initial RAM addr */ 173 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* size */ 174 175 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 176 GENERATED_GBL_DATA_SIZE) 177 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 178 179 #define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB */ 180 #define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Malloc size */ 181 182 /* 183 * Local Bus LCRR and LBCR regs 184 * LCRR: no DLL bypass, Clock divider is 4 185 * External Local Bus rate is 186 * CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV 187 */ 188 #define CONFIG_SYS_LCRR_CLKDIV LCRR_CLKDIV_4 189 #define CONFIG_SYS_LBC_LBCR 0x00000000 190 191 #undef CONFIG_SYS_LB_SDRAM /* if board has SDRAM on local bus */ 192 193 /* 194 * Serial Port 195 */ 196 #define CONFIG_SYS_NS16550_SERIAL 197 #define CONFIG_SYS_NS16550_REG_SIZE 1 198 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 199 200 #define CONFIG_SYS_BAUDRATE_TABLE \ 201 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 202 203 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500) 204 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600) 205 206 /* I2C */ 207 #define CONFIG_SYS_I2C 208 #define CONFIG_SYS_I2C_FSL 209 #define CONFIG_SYS_FSL_I2C_SPEED 400000 210 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 211 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 212 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 213 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 214 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 215 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 216 /* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */ 217 218 #define CONFIG_SYS_I2C_8574_ADDR2 0x20 /* I2C1, PCF8574 */ 219 220 /* TSEC */ 221 #define CONFIG_SYS_TSEC1_OFFSET 0x24000 222 #define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC1_OFFSET) 223 #define CONFIG_SYS_TSEC2_OFFSET 0x25000 224 #define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR + CONFIG_SYS_TSEC2_OFFSET) 225 226 /* 227 * General PCI 228 * Addresses are mapped 1-1. 229 */ 230 #define CONFIG_SYS_PCI1_MEM_BASE 0x80000000 231 #define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE 232 #define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */ 233 #define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000 234 #define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE 235 #define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */ 236 #define CONFIG_SYS_PCI1_IO_BASE 0x00000000 237 #define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000 238 #define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */ 239 240 #define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000 241 #define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE 242 #define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */ 243 #define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000 244 #define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE 245 #define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */ 246 #define CONFIG_SYS_PCI2_IO_BASE 0x00000000 247 #define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000 248 #define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */ 249 250 #if defined(CONFIG_PCI) 251 252 #define PCI_64BIT 253 #define PCI_ONE_PCI1 254 #if defined(PCI_64BIT) 255 #undef PCI_ALL_PCI1 256 #undef PCI_TWO_PCI1 257 #undef PCI_ONE_PCI1 258 #endif 259 260 #undef CONFIG_EEPRO100 261 #undef CONFIG_TULIP 262 263 #if !defined(CONFIG_PCI_PNP) 264 #define PCI_ENET0_IOADDR 0xFIXME 265 #define PCI_ENET0_MEMADDR 0xFIXME 266 #define PCI_IDSEL_NUMBER 0xFIXME 267 #endif 268 269 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 270 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957 /* Freescale */ 271 272 #endif /* CONFIG_PCI */ 273 274 /* 275 * TSEC configuration 276 */ 277 278 #if defined(CONFIG_TSEC_ENET) 279 280 #define CONFIG_GMII /* MII PHY management */ 281 #define CONFIG_TSEC1 282 #define CONFIG_TSEC1_NAME "TSEC0" 283 #define CONFIG_TSEC2 284 #define CONFIG_TSEC2_NAME "TSEC1" 285 #define CONFIG_PHY_M88E1111 286 #define TSEC1_PHY_ADDR 0x08 287 #define TSEC2_PHY_ADDR 0x10 288 #define TSEC1_PHYIDX 0 289 #define TSEC2_PHYIDX 0 290 #define TSEC1_FLAGS TSEC_GIGABIT 291 #define TSEC2_FLAGS TSEC_GIGABIT 292 293 /* Options are: TSEC[0-1] */ 294 #define CONFIG_ETHPRIME "TSEC0" 295 296 #endif /* CONFIG_TSEC_ENET */ 297 298 /* 299 * Environment 300 */ 301 #ifndef CONFIG_SYS_RAMBOOT 302 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0xc0000) 303 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */ 304 #define CONFIG_ENV_SIZE 0x2000 305 306 /* Address and size of Redundant Environment Sector */ 307 #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) 308 #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) 309 310 #else 311 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 312 #define CONFIG_ENV_SIZE 0x2000 313 #endif 314 315 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 316 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 317 318 /* 319 * BOOTP options 320 */ 321 #define CONFIG_BOOTP_BOOTFILESIZE 322 323 /* 324 * Command line configuration. 325 */ 326 #define CONFIG_SYS_RTC_BUS_NUM 0x01 327 #define CONFIG_SYS_I2C_RTC_ADDR 0x32 328 #define CONFIG_RTC_RX8025 329 330 /* Pass Ethernet MAC to VxWorks */ 331 #define CONFIG_SYS_VXWORKS_MAC_PTR 0x000043f0 332 333 #undef CONFIG_WATCHDOG /* watchdog disabled */ 334 335 /* 336 * Miscellaneous configurable options 337 */ 338 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 339 340 /* 341 * For booting Linux, the board info and command line data 342 * have to be in the first 256 MB of memory, since this is 343 * the maximum mapped by the Linux kernel during initialization. 344 */ 345 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Init Memory map for Linux*/ 346 347 #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */ 348 349 #define CONFIG_SYS_HRCW_LOW (\ 350 HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\ 351 HRCWL_DDR_TO_SCB_CLK_1X1 |\ 352 HRCWL_CSB_TO_CLKIN |\ 353 HRCWL_VCO_1X2 |\ 354 HRCWL_CORE_TO_CSB_2X1) 355 356 #if defined(PCI_64BIT) 357 #define CONFIG_SYS_HRCW_HIGH (\ 358 HRCWH_PCI_HOST |\ 359 HRCWH_64_BIT_PCI |\ 360 HRCWH_PCI1_ARBITER_ENABLE |\ 361 HRCWH_PCI2_ARBITER_DISABLE |\ 362 HRCWH_CORE_ENABLE |\ 363 HRCWH_FROM_0X00000100 |\ 364 HRCWH_BOOTSEQ_DISABLE |\ 365 HRCWH_SW_WATCHDOG_DISABLE |\ 366 HRCWH_ROM_LOC_LOCAL_16BIT |\ 367 HRCWH_TSEC1M_IN_GMII |\ 368 HRCWH_TSEC2M_IN_GMII) 369 #else 370 #define CONFIG_SYS_HRCW_HIGH (\ 371 HRCWH_PCI_HOST |\ 372 HRCWH_32_BIT_PCI |\ 373 HRCWH_PCI1_ARBITER_ENABLE |\ 374 HRCWH_PCI2_ARBITER_ENABLE |\ 375 HRCWH_CORE_ENABLE |\ 376 HRCWH_FROM_0X00000100 |\ 377 HRCWH_BOOTSEQ_DISABLE |\ 378 HRCWH_SW_WATCHDOG_DISABLE |\ 379 HRCWH_ROM_LOC_LOCAL_16BIT |\ 380 HRCWH_TSEC1M_IN_GMII |\ 381 HRCWH_TSEC2M_IN_GMII) 382 #endif 383 384 /* System IO Config */ 385 #define CONFIG_SYS_SICRH 0 386 #define CONFIG_SYS_SICRL SICRL_LDP_A 387 388 #define CONFIG_SYS_HID0_INIT 0x000000000 389 #define CONFIG_SYS_HID0_FINAL (HID0_ENABLE_MACHINE_CHECK | \ 390 HID0_ENABLE_INSTRUCTION_CACHE) 391 392 #define CONFIG_SYS_HID2 HID2_HBE 393 394 #define CONFIG_SYS_GPIO1_PRELIM 395 #define CONFIG_SYS_GPIO1_DIR 0x00100000 396 #define CONFIG_SYS_GPIO1_DAT 0x00100000 397 398 #define CONFIG_SYS_GPIO2_PRELIM 399 #define CONFIG_SYS_GPIO2_DIR 0x78900000 400 #define CONFIG_SYS_GPIO2_DAT 0x70100000 401 402 #define CONFIG_HIGH_BATS /* High BATs supported */ 403 404 /* DDR @ 0x00000000 */ 405 #define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE | BATL_PP_RW | \ 406 BATL_MEMCOHERENCE) 407 #define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | \ 408 BATU_VS | BATU_VP) 409 410 /* PCI @ 0x80000000 */ 411 #ifdef CONFIG_PCI 412 #define CONFIG_PCI_INDIRECT_BRIDGE 413 #define CONFIG_SYS_IBAT1L (CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_RW | \ 414 BATL_MEMCOHERENCE) 415 #define CONFIG_SYS_IBAT1U (CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | \ 416 BATU_VS | BATU_VP) 417 #define CONFIG_SYS_IBAT2L (CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_RW | \ 418 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 419 #define CONFIG_SYS_IBAT2U (CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | \ 420 BATU_VS | BATU_VP) 421 #else 422 #define CONFIG_SYS_IBAT1L (0) 423 #define CONFIG_SYS_IBAT1U (0) 424 #define CONFIG_SYS_IBAT2L (0) 425 #define CONFIG_SYS_IBAT2U (0) 426 #endif 427 428 #ifdef CONFIG_MPC83XX_PCI2 429 #define CONFIG_SYS_IBAT3L (CONFIG_SYS_PCI2_MEM_BASE | BATL_PP_RW | \ 430 BATL_MEMCOHERENCE) 431 #define CONFIG_SYS_IBAT3U (CONFIG_SYS_PCI2_MEM_BASE | BATU_BL_256M | \ 432 BATU_VS | BATU_VP) 433 #define CONFIG_SYS_IBAT4L (CONFIG_SYS_PCI2_MMIO_BASE | BATL_PP_RW | \ 434 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 435 #define CONFIG_SYS_IBAT4U (CONFIG_SYS_PCI2_MMIO_BASE | BATU_BL_256M | \ 436 BATU_VS | BATU_VP) 437 #else 438 #define CONFIG_SYS_IBAT3L (0) 439 #define CONFIG_SYS_IBAT3U (0) 440 #define CONFIG_SYS_IBAT4L (0) 441 #define CONFIG_SYS_IBAT4U (0) 442 #endif 443 444 /* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 */ 445 #define CONFIG_SYS_IBAT5L (CONFIG_SYS_IMMR | BATL_PP_RW | \ 446 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 447 #define CONFIG_SYS_IBAT5U (CONFIG_SYS_IMMR | BATU_BL_256M | \ 448 BATU_VS | BATU_VP) 449 450 #define CONFIG_SYS_IBAT6L (0xF0000000 | BATL_PP_RW | BATL_MEMCOHERENCE) 451 #define CONFIG_SYS_IBAT6U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP) 452 453 #if (CONFIG_SYS_DDR_SIZE == 512) 454 #define CONFIG_SYS_IBAT7L (CONFIG_SYS_SDRAM_BASE+0x10000000 | \ 455 BATL_PP_RW | BATL_MEMCOHERENCE) 456 #define CONFIG_SYS_IBAT7U (CONFIG_SYS_SDRAM_BASE+0x10000000 | \ 457 BATU_BL_256M | BATU_VS | BATU_VP) 458 #else 459 #define CONFIG_SYS_IBAT7L (0) 460 #define CONFIG_SYS_IBAT7U (0) 461 #endif 462 463 #define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L 464 #define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U 465 #define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L 466 #define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U 467 #define CONFIG_SYS_DBAT2L CONFIG_SYS_IBAT2L 468 #define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U 469 #define CONFIG_SYS_DBAT3L CONFIG_SYS_IBAT3L 470 #define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U 471 #define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L 472 #define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U 473 #define CONFIG_SYS_DBAT5L CONFIG_SYS_IBAT5L 474 #define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U 475 #define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L 476 #define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U 477 #define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L 478 #define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U 479 480 #if defined(CONFIG_CMD_KGDB) 481 #define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */ 482 #endif 483 484 /* 485 * Environment Configuration 486 */ 487 #define CONFIG_ENV_OVERWRITE 488 489 #if defined(CONFIG_TSEC_ENET) 490 #define CONFIG_HAS_ETH0 491 #define CONFIG_HAS_ETH1 492 #endif 493 494 #define CONFIG_HOSTNAME "VME8349" 495 #define CONFIG_ROOTPATH "/tftpboot/rootfs" 496 #define CONFIG_BOOTFILE "uImage" 497 498 #define CONFIG_LOADADDR 800000 /* def location for tftp and bootm */ 499 500 #define CONFIG_EXTRA_ENV_SETTINGS \ 501 "netdev=eth0\0" \ 502 "hostname=vme8349\0" \ 503 "nfsargs=setenv bootargs root=/dev/nfs rw " \ 504 "nfsroot=${serverip}:${rootpath}\0" \ 505 "ramargs=setenv bootargs root=/dev/ram rw\0" \ 506 "addip=setenv bootargs ${bootargs} " \ 507 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ 508 ":${hostname}:${netdev}:off panic=1\0" \ 509 "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\ 510 "flash_nfs=run nfsargs addip addtty;" \ 511 "bootm ${kernel_addr}\0" \ 512 "flash_self=run ramargs addip addtty;" \ 513 "bootm ${kernel_addr} ${ramdisk_addr}\0" \ 514 "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ 515 "bootm\0" \ 516 "load=tftp 100000 /tftpboot/bdi2000/vme8349.bin\0" \ 517 "update=protect off fff00000 fff3ffff; " \ 518 "era fff00000 fff3ffff; cp.b 100000 fff00000 ${filesize}\0" \ 519 "upd=run load update\0" \ 520 "fdtaddr=780000\0" \ 521 "fdtfile=vme8349.dtb\0" \ 522 "" 523 524 #define CONFIG_NFSBOOTCOMMAND \ 525 "setenv bootargs root=/dev/nfs rw " \ 526 "nfsroot=$serverip:$rootpath " \ 527 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \ 528 "$netdev:off " \ 529 "console=$consoledev,$baudrate $othbootargs;" \ 530 "tftp $loadaddr $bootfile;" \ 531 "tftp $fdtaddr $fdtfile;" \ 532 "bootm $loadaddr - $fdtaddr" 533 534 #define CONFIG_RAMBOOTCOMMAND \ 535 "setenv bootargs root=/dev/ram rw " \ 536 "console=$consoledev,$baudrate $othbootargs;" \ 537 "tftp $ramdiskaddr $ramdiskfile;" \ 538 "tftp $loadaddr $bootfile;" \ 539 "tftp $fdtaddr $fdtfile;" \ 540 "bootm $loadaddr $ramdiskaddr $fdtaddr" 541 542 #define CONFIG_BOOTCOMMAND "run flash_self" 543 544 #ifndef __ASSEMBLY__ 545 int vme8349_read_spd(unsigned char chip, unsigned int addr, int alen, 546 unsigned char *buffer, int len); 547 #endif 548 549 #endif /* __CONFIG_H */ 550
