1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * (C) Copyright 2012-2013 4 * Texas Instruments, <www.ti.com> 5 */ 6 #include <config.h> 7 #include <palmas.h> 8 9 void palmas_init_settings(void) 10 { 11 #ifdef CONFIG_PALMAS_SMPS7_FPWM 12 int err; 13 /* 14 * Set SMPS7 (1.8 V I/O supply on platforms with TWL6035/37) to 15 * forced PWM mode. This reduces noise (but affects efficiency). 16 */ 17 u8 val = SMPS_MODE_SLP_FPWM | SMPS_MODE_ACT_FPWM; 18 err = palmas_i2c_write_u8(TWL603X_CHIP_P1, SMPS7_CTRL, val); 19 if (err) 20 printf("palmas: could not force PWM for SMPS7: err = %d\n", 21 err); 22 #endif 23 } 24 25 #if defined(CONFIG_OMAP54XX) 26 int lp873x_mmc1_poweron_ldo(uint voltage) 27 { 28 if (palmas_i2c_write_u8(LP873X_LDO1_ADDR, LP873X_LDO1_VOLTAGE, 29 voltage)) { 30 printf("lp873x: could not set LDO1 voltage.\n"); 31 return 1; 32 } 33 /* TURN ON LDO1 */ 34 if (palmas_i2c_write_u8(LP873X_LDO1_ADDR, LP873X_LDO1_CTRL, 35 LP873X_LDO_CTRL_EN | LP873X_LDO_CTRL_RDIS_EN)) { 36 printf("lp873x: could not turn on LDO1.\n"); 37 return 1; 38 } 39 return 0; 40 41 } 42 #endif 43 44 int palmas_mmc1_poweron_ldo(uint ldo_volt, uint ldo_ctrl, uint voltage) 45 { 46 u8 val = 0; 47 48 #if defined(CONFIG_DRA7XX) 49 int ret; 50 51 ret = palmas_i2c_write_u8(TPS65903X_CHIP_P1, ldo_volt, voltage); 52 if (ret) { 53 printf("tps65903x: could not set LDO1 voltage.\n"); 54 return ret; 55 } 56 /* TURN ON LDO1 */ 57 val = RSC_MODE_SLEEP | RSC_MODE_ACTIVE; 58 ret = palmas_i2c_write_u8(TPS65903X_CHIP_P1, ldo_ctrl, val); 59 if (ret) { 60 printf("tps65903x: could not turn on LDO1.\n"); 61 return ret; 62 } 63 return 0; 64 #else 65 /* 66 * We assume that this is a OMAP543X + TWL603X board: 67 * Set TWL6035/37 LDO9 to 3.0 V 68 */ 69 val = LDO_VOLT_3V0; 70 return twl603x_mmc1_set_ldo9(val); 71 #endif 72 } 73 74 /* 75 * On some OMAP5 + TWL603X hardware the SD card socket and LDO9_IN are 76 * powered by an external 3.3 V regulator, while the output of LDO9 77 * supplies VDDS_SDCARD for the OMAP5 interface only. This implies that 78 * LDO9 could be set to 'bypass' mode when required (e.g. for 3.3 V cards). 79 */ 80 int twl603x_mmc1_set_ldo9(u8 vsel) 81 { 82 u8 cval = 0, vval = 0; /* Off by default */ 83 int err; 84 85 if (vsel) { 86 /* Turn on */ 87 if (vsel > LDO_VOLT_3V3) { 88 /* Put LDO9 in bypass */ 89 cval = LDO9_BYP_EN | RSC_MODE_SLEEP | RSC_MODE_ACTIVE; 90 vval = LDO_VOLT_3V3; 91 } else { 92 cval = RSC_MODE_SLEEP | RSC_MODE_ACTIVE; 93 vval = vsel & 0x3f; 94 } 95 } 96 err = palmas_i2c_write_u8(TWL603X_CHIP_P1, LDO9_VOLTAGE, vval); 97 if (err) { 98 printf("twl603x: could not set LDO9 %s: err = %d\n", 99 vsel > LDO_VOLT_3V3 ? "bypass" : "voltage", err); 100 return err; 101 } 102 err = palmas_i2c_write_u8(TWL603X_CHIP_P1, LDO9_CTRL, cval); 103 if (err) 104 printf("twl603x: could not turn %s LDO9: err = %d\n", 105 cval ? "on" : "off", err); 106 return err; 107 } 108 109 #ifdef CONFIG_PALMAS_AUDPWR 110 /* 111 * Turn audio codec power and 32 kHz clock on/off. Use for 112 * testing OMAP543X + TWL603X + TWL604X boards only. 113 */ 114 int twl603x_audio_power(u8 on) 115 { 116 u8 cval = 0, vval = 0, c32k = 0; 117 int err; 118 119 if (on) { 120 vval = SMPS_VOLT_2V1; 121 cval = SMPS_MODE_SLP_AUTO | SMPS_MODE_ACT_AUTO; 122 c32k = RSC_MODE_SLEEP | RSC_MODE_ACTIVE; 123 } 124 /* Set SMPS9 to 2.1 V (for TWL604x), or to 0 (off) */ 125 err = palmas_i2c_write_u8(TWL603X_CHIP_P1, SMPS9_VOLTAGE, vval); 126 if (err) { 127 printf("twl603x: could not set SMPS9 voltage: err = %d\n", 128 err); 129 return err; 130 } 131 /* Turn on or off SMPS9 */ 132 err = palmas_i2c_write_u8(TWL603X_CHIP_P1, SMPS9_CTRL, cval); 133 if (err) { 134 printf("twl603x: could not turn SMPS9 %s: err = %d\n", 135 cval ? "on" : "off", err); 136 return err; 137 } 138 /* Output 32 kHz clock on or off */ 139 err = palmas_i2c_write_u8(TWL603X_CHIP_P1, CLK32KGAUDIO_CTRL, c32k); 140 if (err) 141 printf("twl603x: could not turn CLK32KGAUDIO %s: err = %d\n", 142 c32k ? "on" : "off", err); 143 return err; 144 } 145 #endif 146 147 #ifdef CONFIG_PALMAS_USB_SS_PWR 148 /** 149 * @brief palmas_enable_ss_ldo - Configure EVM board specific configurations 150 * for the USB Super speed SMPS10 regulator. 151 * 152 * @return 0 153 */ 154 int palmas_enable_ss_ldo(void) 155 { 156 /* Enable smps10 regulator */ 157 return palmas_i2c_write_u8(TWL603X_CHIP_P1, SMPS10_CTRL, 158 SMPS10_MODE_ACTIVE_D); 159 } 160 #endif 161 162 /* 163 * Enable/disable back-up battery (or super cap) charging on TWL6035/37. 164 * Please use defined BB_xxx values. 165 */ 166 int twl603x_enable_bb_charge(u8 bb_fields) 167 { 168 u8 val = bb_fields & 0x0f; 169 int err; 170 171 val |= (VRTC_EN_SLP | VRTC_EN_OFF | VRTC_PWEN); 172 err = palmas_i2c_write_u8(TWL603X_CHIP_P1, BB_VRTC_CTRL, val); 173 if (err) 174 printf("twl603x: could not set BB_VRTC_CTRL to 0x%02x: err = %d\n", 175 val, err); 176 return err; 177 } 178
