Lines Matching full:capture
1199 capture rate relative to sensor raw output.<wbr/></p>
1209 quality but the capture rate might be reduced (relative to sensor
1290 capture rate,<wbr/> then FAST and HIGH_<wbr/>QUALITY should generate the same output.<wbr/></p>
1460 <span class="entry_type_enum_notes"><p>Aberration correction will not slow down capture rate
1465 <span class="entry_type_enum_notes"><p>Aberration correction operates at improved quality but the capture rate might be
1500 capture rate.<wbr/> FAST means the camera device will not slow down capture rate when
1567 capture rate relative to sensor raw output.<wbr/></p>
1577 quality but the capture rate might be reduced (relative to sensor
1658 capture rate,<wbr/> then FAST and HIGH_<wbr/>QUALITY should generate the same output.<wbr/></p>
1828 <span class="entry_type_enum_notes"><p>Aberration correction will not slow down capture rate
1833 <span class="entry_type_enum_notes"><p>Aberration correction operates at improved quality but the capture rate might be
1868 capture rate.<wbr/> FAST means the camera device will not slow down capture rate when
1970 capture rate,<wbr/> then FAST and HIGH_<wbr/>QUALITY will generate the same output.<wbr/></p>
2114 <p>For all capture request templates,<wbr/> this field must be set
2186 FLASH_<wbr/>REQUIRED (if the scene is too dark for still capture).<wbr/></p>
2275 latest capture result received from the camera device,<wbr/> since additional captures
2284 <li>Submit the capture request,<wbr/> proceed to run manual AE as desired.<wbr/></li>
2349 <a href="#controls_android.control.captureIntent">android.<wbr/>control.<wbr/>capture<wbr/>Intent</a> field is set to
2350 STILL_<wbr/>CAPTURE</p></span>
2360 <a href="#controls_android.control.captureIntent">android.<wbr/>control.<wbr/>capture<wbr/>Intent</a> field is set to
2361 STILL_<wbr/>CAPTURE</p></span>
2415 fields for a given capture will be available in its
2491 capture result metadata,<wbr/> the camera device will ignore the sections outside the crop
2540 adjust the capture frame rate to maintain good
2642 device has implicitly locked the AE for subsequent still capture,<wbr/> the
2645 high-quality still capture for final metering decisions to
2646 be made,<wbr/> and for firing pre-capture flash pulses to estimate
2647 scene brightness and required final capture flash power,<wbr/> when
2654 subsequent still capture image (<code><a href="#controls_android.control.captureIntent">android.<wbr/>control.<wbr/>capture<wbr/>Intent</a> == STILL_<wbr/>CAPTURE</code>).<wbr/>
2655 For this case,<wbr/> the AE may not resume normal scan if no subsequent still capture is
2659 still capture request after the precapture sequence completes.<wbr/> Alternatively,<wbr/> for
2661 internally locked AE if the application doesn't submit a still capture request after
2670 precapture sequence before the high-resolution capture,<wbr/> including
2671 potentially firing a pre-capture flash.<wbr/></p>
2777 capture; typically this means focusing as fast as
2936 capture result metadata,<wbr/> the camera device will ignore the sections outside the crop
3023 single capture,<wbr/> and then return it to IDLE (or not set at all).<wbr/> Specifying
3112 latest capture result received from the camera device,<wbr/> since additional captures
3121 <li>Submit the capture request,<wbr/> proceed to run manual AWB as desired.<wbr/></li>
3166 will be available in the capture result for this request.<wbr/></p></span>
3180 will be available in the capture result for this request.<wbr/></p></span>
3194 will be available in the capture result for this request.<wbr/></p></span>
3208 will be available in the capture result for this request.<wbr/></p></span>
3222 will be available in the capture result for this request.<wbr/></p></span>
3233 will be available in the capture result for this request.<wbr/></p></span>
3244 will be available in the capture result for this request.<wbr/></p></span>
3255 will be available in the capture result for this request.<wbr/></p></span>
3380 capture result metadata,<wbr/> the camera device will ignore the sections outside the crop
3408 android.<wbr/>control.<wbr/>capture<wbr/>Intent
3435 <span class="entry_type_enum_notes"><p>This request is for a still capture-type
3457 capture.<wbr/></p></span>
3461 <span class="entry_type_enum_notes"><p>This request is for manual capture use case where
3462 the applications want to directly control the capture parameters.<wbr/></p>
3473 of this capture,<wbr/> to help the camera device to decide optimal 3A
3642 <a href="#controls_android.control.captureIntent">android.<wbr/>control.<wbr/>capture<wbr/>Intent</a> may be used by the camera
3654 <p>Manual control of capture parameters is disabled.<wbr/> All
3673 <span class="entry_type_enum_notes"><p>Same as OFF mode,<wbr/> except that this capture will not be
3712 capture parameters itself.<wbr/></p>
3719 <a href="https://developer.android.com/reference/android/hardware/camera2/CaptureResult.html">capture results</a>.<wbr/></p>
3723 where the application doesn't want a 3A manual control capture to affect
3724 the subsequent auto 3A capture results.<wbr/></p>
3752 <span class="entry_type_enum_notes"><p>Indicates that no scene modes are set for a given capture request.<wbr/></p></span>
3866 controls will be overridden to be FAST.<wbr/> Therefore,<wbr/> no manual control of capture
3884 <li><a href="#controls_android.flash.mode">android.<wbr/>flash.<wbr/>mode</a> (automatic flash for still capture will not work since aeMode is ON)</li>
3910 and the returned capture result metadata will give the fps range choosen
3927 HDR mode generally takes much longer to capture a single
3933 is made with a <a href="#controls_android.control.captureIntent">android.<wbr/>control.<wbr/>capture<wbr/>Intent</a> of
3934 STILL_<wbr/>CAPTURE,<wbr/> the camera device will capture an image
3935 using a high dynamic range capture technique.<wbr/> On LEGACY
3937 be captured with HDR,<wbr/> and the capture intent is not
3939 <p>The HDR capture may involve the device capturing a burst
3942 range capture hardware.<wbr/> In all cases,<wbr/> a single image is
3943 produced in response to a capture request submitted
3949 captures.<wbr/> Using a RAW output for HDR capture is not
4006 capture settings.<wbr/></p>
4031 mode and high speed streaming,<wbr/> when this scene mode is set/<wbr/>reset in a sequence of capture
4100 in capture result metadata.<wbr/> For example,<wbr/> When "ON" mode is requested,<wbr/>
4101 the video stabilization modes in the first several capture results may
4333 <li>For YUV_<wbr/>420_<wbr/>888 burst capture use case,<wbr/> this list will always include (<code>min</code>,<wbr/> <code>max</code>)
5148 must have the same size).<wbr/> Otherwise,<wbr/> the high speed capture session creation will fail.<wbr/></p>
5170 that are submitted to a high speed camera capture session created by
5172 The fps ranges reported in this metadata must not be used to setup capture requests for
5173 normal capture session,<wbr/> or it will cause request error.<wbr/></p>
5254 <p>Devices with MANUAL_<wbr/>SENSOR capability or BURST_<wbr/>CAPTURE capability will always
5312 <p>Devices with MANUAL_<wbr/>POST_<wbr/>PROCESSING capability or BURST_<wbr/>CAPTURE capability will
5560 <p>For all capture request templates,<wbr/> this field must be set
5632 FLASH_<wbr/>REQUIRED (if the scene is too dark for still capture).<wbr/></p>
5721 latest capture result received from the camera device,<wbr/> since additional captures
5730 <li>Submit the capture request,<wbr/> proceed to run manual AE as desired.<wbr/></li>
5795 <a href="#controls_android.control.captureIntent">android.<wbr/>control.<wbr/>capture<wbr/>Intent</a> field is set to
5796 STILL_<wbr/>CAPTURE</p></span>
5806 <a href="#controls_android.control.captureIntent">android.<wbr/>control.<wbr/>capture<wbr/>Intent</a> field is set to
5807 STILL_<wbr/>CAPTURE</p></span>
5861 fields for a given capture will be available in its
5937 capture result metadata,<wbr/> the camera device will ignore the sections outside the crop
5986 adjust the capture frame rate to maintain good
6088 device has implicitly locked the AE for subsequent still capture,<wbr/> the
6091 high-quality still capture for final metering decisions to
6092 be made,<wbr/> and for firing pre-capture flash pulses to estimate
6093 scene brightness and required final capture flash power,<wbr/> when
6100 subsequent still capture image (<code><a href="#controls_android.control.captureIntent">android.<wbr/>control.<wbr/>capture<wbr/>Intent</a> == STILL_<wbr/>CAPTURE</code>).<wbr/>
6101 For this case,<wbr/> the AE may not resume normal scan if no subsequent still capture is
6105 still capture request after the precapture sequence completes.<wbr/> Alternatively,<wbr/> for
6107 internally locked AE if the application doesn't submit a still capture request after
6116 precapture sequence before the high-resolution capture,<wbr/> including
6117 potentially firing a pre-capture flash.<wbr/></p>
6168 this state in capture result.<wbr/></p></span>
6175 reporting this state in capture result.<wbr/></p></span>
6190 capture.<wbr/></p></span>
6204 capture result.<wbr/></p></span>
6345 <td align="center">Ready for high-quality capture</td>
6351 <td align="center">Ready for high-quality capture</td>
6523 capture; typically this means focusing as fast as
6682 capture result metadata,<wbr/> the camera device will ignore the sections outside the crop
6769 single capture,<wbr/> and then return it to IDLE (or not set at all).<wbr/> Specifying
6821 skip reporting this state in capture
6830 capture result.<wbr/></p></span>
6838 capture result.<wbr/></p></span>
6846 capture result.<wbr/></p></span>
6871 device may skip reporting this state in capture result.<wbr/></p>
7396 latest capture result received from the camera device,<wbr/> since additional captures
7405 <li>Submit the capture request,<wbr/> proceed to run manual AWB as desired.<wbr/></li>
7450 will be available in the capture result for this request.<wbr/></p></span>
7464 will be available in the capture result for this request.<wbr/></p></span>
7478 will be available in the capture result for this request.<wbr/></p></span>
7492 will be available in the capture result for this request.<wbr/></p></span>
7506 will be available in the capture result for this request.<wbr/></p></span>
7517 will be available in the capture result for this request.<wbr/></p></span>
7528 will be available in the capture result for this request.<wbr/></p></span>
7539 will be available in the capture result for this request.<wbr/></p></span>
7664 capture result metadata,<wbr/> the camera device will ignore the sections outside the crop
7692 android.<wbr/>control.<wbr/>capture<wbr/>Intent
7719 <span class="entry_type_enum_notes"><p>This request is for a still capture-type
7741 capture.<wbr/></p></span>
7745 <span class="entry_type_enum_notes"><p>This request is for manual capture use case where
7746 the applications want to directly control the capture parameters.<wbr/></p>
7757 of this capture,<wbr/> to help the camera device to decide optimal 3A
7814 skip reporting this state in capture
7822 may skip reporting this state in capture result.<wbr/></p></span>
8112 <a href="#controls_android.control.captureIntent">android.<wbr/>control.<wbr/>capture<wbr/>Intent</a> may be used by the camera
8124 <p>Manual control of capture parameters is disabled.<wbr/> All
8143 <span class="entry_type_enum_notes"><p>Same as OFF mode,<wbr/> except that this capture will not be
8182 capture parameters itself.<wbr/></p>
8189 <a href="https://developer.android.com/reference/android/hardware/camera2/CaptureResult.html">capture results</a>.<wbr/></p>
8193 where the application doesn't want a 3A manual control capture to affect
8194 the subsequent auto 3A capture results.<wbr/></p>
8222 <span class="entry_type_enum_notes"><p>Indicates that no scene modes are set for a given capture request.<wbr/></p></span>
8336 controls will be overridden to be FAST.<wbr/> Therefore,<wbr/> no manual control of capture
8354 <li><a href="#controls_android.flash.mode">android.<wbr/>flash.<wbr/>mode</a> (automatic flash for still capture will not work since aeMode is ON)</li>
8380 and the returned capture result metadata will give the fps range choosen
8397 HDR mode generally takes much longer to capture a single
8403 is made with a <a href="#controls_android.control.captureIntent">android.<wbr/>control.<wbr/>capture<wbr/>Intent</a> of
8404 STILL_<wbr/>CAPTURE,<wbr/> the camera device will capture an image
8405 using a high dynamic range capture technique.<wbr/> On LEGACY
8407 be captured with HDR,<wbr/> and the capture intent is not
8409 <p>The HDR capture may involve the device capturing a burst
8412 range capture hardware.<wbr/> In all cases,<wbr/> a single image is
8413 produced in response to a capture request submitted
8419 captures.<wbr/> Using a RAW output for HDR capture is not
8476 capture settings.<wbr/></p>
8501 mode and high speed streaming,<wbr/> when this scene mode is set/<wbr/>reset in a sequence of capture
8570 in capture result metadata.<wbr/> For example,<wbr/> When "ON" mode is requested,<wbr/>
8571 the video stabilization modes in the first several capture results may
8789 even if it slows down capture rate.<wbr/> FAST means the camera device will
8790 not slow down capture rate when applying edge enhancement.<wbr/> FAST may be the same as OFF if
8791 edge enhancement will slow down capture rate.<wbr/> Every output stream will have a similar
8795 into a final capture when triggered by the user.<wbr/> In this mode,<wbr/> the camera device applies
8952 capture rate,<wbr/> then FAST and HIGH_<wbr/>QUALITY will generate the same output.<wbr/></p>
9073 even if it slows down capture rate.<wbr/> FAST means the camera device will
9074 not slow down capture rate when applying edge enhancement.<wbr/> FAST may be the same as OFF if
9075 edge enhancement will slow down capture rate.<wbr/> Every output stream will have a similar
9079 into a final capture when triggered by the user.<wbr/> In this mode,<wbr/> the camera device applies
9259 <span class="entry_type_enum_notes"><p>Do not fire the flash for this capture.<wbr/></p></span>
9264 for this capture.<wbr/></p></span>
9301 <p>When set to OFF,<wbr/> the camera device will not fire flash for this capture.<wbr/></p>
9303 device's auto-exposure routine's result.<wbr/> When used in still capture case,<wbr/> this
9307 for use cases such as preview,<wbr/> auto-focus assist,<wbr/> still capture,<wbr/> or video recording.<wbr/></p>
9308 <p>The flash status will be reported by <a href="#dynamic_android.flash.state">android.<wbr/>flash.<wbr/>state</a> in the capture result metadata.<wbr/></p>
9696 <span class="entry_type_enum_notes"><p>Do not fire the flash for this capture.<wbr/></p></span>
9701 for this capture.<wbr/></p></span>
9738 <p>When set to OFF,<wbr/> the camera device will not fire flash for this capture.<wbr/></p>
9740 device's auto-exposure routine's result.<wbr/> When used in still capture case,<wbr/> this
9744 for use cases such as preview,<wbr/> auto-focus assist,<wbr/> still capture,<wbr/> or video recording.<wbr/></p>
9745 <p>The flash status will be reported by <a href="#dynamic_android.flash.state">android.<wbr/>flash.<wbr/>state</a> in the capture result metadata.<wbr/></p>
9784 <span class="entry_type_enum_notes"><p>Flash fired for this capture.<wbr/></p></span>
9790 the flash fire,<wbr/> and the flash spilling into this capture
10031 capture rate,<wbr/> then FAST and HIGH_<wbr/>QUALITY will generate the same output.<wbr/></p>
10589 capture result,<wbr/> so the width and height will be interchanged if 90 or 270 degree
11140 if <a href="#static_android.jpeg.maxSize">android.<wbr/>jpeg.<wbr/>max<wbr/>Size</a> = 1000000,<wbr/> and a specific capture
11258 capture result,<wbr/> so the width and height will be interchanged if 90 or 270 degree
11364 aperture size in capture result metadata while the aperture is changing.<wbr/>
11616 movements of the camera during capture.<wbr/> Unlike digital image
11623 capture result metadata.<wbr/> For example,<wbr/> When "ON" mode is requested,<wbr/> the
11624 optical stabilization modes in the first several capture results may still
12658 aperture size in capture result metadata while the aperture is changing.<wbr/>
12958 movements of the camera during capture.<wbr/> Unlike digital image
12965 capture result metadata.<wbr/> For example,<wbr/> When "ON" mode is requested,<wbr/> the
12966 optical stabilization modes in the first several capture results may still
13526 excessive noise added by the capture process,<wbr/> especially in dark conditions.<wbr/></p>
13536 even if it slows down capture rate.<wbr/> FAST means the camera device will not
13537 slow down capture rate when applying noise filtering.<wbr/> FAST may be the same as MINIMAL if
13538 MINIMAL is listed,<wbr/> or the same as OFF if any noise filtering will slow down capture rate.<wbr/>
13542 into a final capture when triggered by the user.<wbr/> In this mode,<wbr/> the camera device applies
13701 capture rate,<wbr/> then FAST and HIGH_<wbr/>QUALITY will generate the same output.<wbr/></p>
13825 excessive noise added by the capture process,<wbr/> especially in dark conditions.<wbr/></p>
13835 even if it slows down capture rate.<wbr/> FAST means the camera device will not
13836 slow down capture rate when applying noise filtering.<wbr/> FAST may be the same as MINIMAL if
13837 MINIMAL is listed,<wbr/> or the same as OFF if any noise filtering will slow down capture rate.<wbr/>
13841 into a final capture when triggered by the user.<wbr/> In this mode,<wbr/> the camera device applies
14087 metadata for a single capture into multiple buffers,<wbr/>
14176 for this capture.<wbr/></p></span>
14181 capture.<wbr/> More result buffers for this capture will be sent
14191 final one for the capture,<wbr/> or only a partial that contains a
14214 single capture may not overlap,<wbr/> except for this entry.<wbr/> The
14220 capture must arrive before the FINAL buffer for that capture.<wbr/> This entry may
14504 from this capture must be sent to</p>
14559 <span class="entry_type_enum_name">CAPTURE</span>
14560 <span class="entry_type_enum_notes"><p>Capture a new image from the imaging hardware,<wbr/>
14576 <p>The type of the request; either CAPTURE or
15004 <p>For example,<wbr/> for Zero Shutter Lag (ZSL) still capture use case,<wbr/> the input
15073 <p>This value will normally be 8 or less,<wbr/> however,<wbr/> for high speed capture session,<wbr/>
15074 the max pipeline depth will be up to 8 x size of high speed capture request list.<wbr/></p>
15310 relative to the sensor's maximum capture rate (at that resolution).<wbr/></li>
15317 <li>Static metadata <a href="#static_android.reprocess.maxCaptureStall">android.<wbr/>reprocess.<wbr/>max<wbr/>Capture<wbr/>Stall</a>.<wbr/></li>
15319 will be present in capture results,<wbr/> other controls in reprocess
15379 are also guaranteed to be <code>true</code> so burst capture with these two locks ON yields
15398 relative to the sensor's maximum capture rate (at that resolution).<wbr/></li>
15403 <li>Static metadata <a href="#static_android.reprocess.maxCaptureStall">android.<wbr/>reprocess.<wbr/>max<wbr/>Capture<wbr/>Stall</a>.<wbr/></li>
15405 in capture results.<wbr/> The reprocess requests are from the original capture results that
15443 <p>Generally,<wbr/> depth output operates at a slower frame rate than standard color capture,<wbr/>
15456 use case.<wbr/> The camera device will support high speed capture session created by
15462 capture request per frame control and synchronization requirements will apply to
15474 controls will be overridden to be FAST.<wbr/> Therefore,<wbr/> no manual control of capture
15492 <li><a href="#controls_android.flash.mode">android.<wbr/>flash.<wbr/>mode</a> (TORCH mode only,<wbr/> automatic flash for still capture will not
15509 <li>The application creates a camera capture session with no more than 2 surfaces via
16049 from this capture must be sent to</p>
16202 <p>The desired region of the sensor to read out for this capture.<wbr/></p>
16253 crop region used will be included in the output capture
17385 pipeline,<wbr/> but cannot process more than 1 capture at a time.<wbr/></li>
17681 return the final used crop region in capture result metadata <a href="#controls_android.scaler.cropRegion">android.<wbr/>scaler.<wbr/>crop<wbr/>Region</a>.<wbr/></p>
17741 <p>The desired region of the sensor to read out for this capture.<wbr/></p>
17792 crop region used will be included in the output capture
17926 The final exposure time used will be available in the output capture result.<wbr/></p>
18005 scaling a single capture to all the streams at the same time.<wbr/> This
18015 cannot process more than 1 capture at a time.<wbr/></li>
18042 by a single capture of a new request <code>Rstall</code> (which has at least
18119 output capture result.<wbr/></p>
18711 a single uncompressed capture,<wbr/> refer to
18944 and the result metadata generated by a single capture are identical.<wbr/></p></span>
18957 <p>The time base source for sensor capture start timestamps.<wbr/></p>
20188 The final exposure time used will be available in the output capture result.<wbr/></p>
20267 scaling a single capture to all the streams at the same time.<wbr/> This
20277 cannot process more than 1 capture at a time.<wbr/></li>
20304 by a single capture of a new request <code>Rstall</code> (which has at least
20381 output capture result.<wbr/></p>
20442 buffers produced for the same capture,<wbr/> and will be identical
20456 reprocess capture request.<wbr/></p>
20475 capture request.<wbr/></p>
20551 the time of capture.<wbr/></p>
21271 data will be the one applied by the camera device for this capture request.<wbr/></p>
21427 data will be the one applied by the camera device for this capture request.<wbr/></p>
21526 slow down capture rate,<wbr/> then FAST and HIGH_<wbr/>QUALITY will generate the same output.<wbr/></p>
21584 <span class="entry_type_enum_notes"><p>Do not include face detection statistics in capture
21826 <span class="entry_type_enum_notes"><p>Do not include a lens shading map in the capture result.<wbr/></p></span>
21830 <span class="entry_type_enum_notes"><p>Include a lens shading map in the capture result.<wbr/></p></span>
22331 <span class="entry_type_enum_notes"><p>Do not include face detection statistics in capture
22655 in this capture.<wbr/></p>
23210 capture settings and color transforms are set by the application.<wbr/></p>
23452 <span class="entry_type_enum_notes"><p>Do not include a lens shading map in the capture result.<wbr/></p></span>
23456 <span class="entry_type_enum_notes"><p>Include a lens shading map in the capture result.<wbr/></p></span>
23987 value will be returned in capture result.<wbr/></p>
24209 capture rate,<wbr/> then FAST and HIGH_<wbr/>QUALITY will generate the same output.<wbr/></p>
24701 value will be returned in capture result.<wbr/></p>
25101 <li>BURST_<wbr/>CAPTURE capability (<a href="#static_android.request.availableCapabilities">android.<wbr/>request.<wbr/>available<wbr/>Capabilities</a> contains BURST_<wbr/>CAPTURE)</li>
25242 <p>Since changes to certain capture parameters (such as
25286 does happen) until the next capture for which locking is
25372 ON if <a href="#controls_android.blackLevel.lock">android.<wbr/>black<wbr/>Level.<wbr/>lock</a> was ON in the capture request,<wbr/> unless
25373 a change in other capture settings forced the camera device to
25387 does happen) until the next capture for which locking is
25697 <code>@link{android.<wbr/>hardware.<wbr/>camera2.<wbr/>Capture<wbr/>Result#get<wbr/>Frame<wbr/>Number}</code>.<wbr/></p>
25790 would be expected if the original capture parameters had been a sensitivity of
25809 <p>This control is only effective for YUV reprocessing capture request.<wbr/> For noise
25898 would be expected if the original capture parameters had been a sensitivity of
25917 <p>This control is only effective for YUV reprocessing capture request.<wbr/> For noise
25959 android.<wbr/>reprocess.<wbr/>max<wbr/>Capture<wbr/>Stall
25975 <p>The maximal camera capture pipeline stall (in unit of frame count) introduced by a
25976 reprocess capture request.<wbr/></p>
26000 can introduce to the camera simultaneous streaming of regular (output) capture
26002 <p>When a reprocessing capture request is submitted while a camera output repeating request
26003 (e.<wbr/>g.<wbr/> preview) is being served by the camera device,<wbr/> it may preempt the camera capture
26005 the following capture request in time for the next sensor start of exposure boundary.<wbr/>
26006 When this happens,<wbr/> the application may observe a capture time gap (longer than one frame
26007 duration) between adjacent capture output frames,<wbr/> which usually exhibits as preview
26337 <p>Indicates whether a capture request may target both a
26358 capture request is not supported.<wbr/> An application must interleave color
