1 #ifndef _GPXE_ATA_H 2 #define _GPXE_ATA_H 3 4 #include <stdint.h> 5 #include <gpxe/blockdev.h> 6 #include <gpxe/uaccess.h> 7 #include <gpxe/refcnt.h> 8 9 /** @file 10 * 11 * ATA devices 12 * 13 */ 14 15 FILE_LICENCE ( GPL2_OR_LATER ); 16 17 /** 18 * An ATA Logical Block Address 19 * 20 * ATA controllers have three byte-wide registers for specifying the 21 * block address: LBA Low, LBA Mid and LBA High. This allows for a 22 * 24-bit address. Some devices support the "48-bit address feature 23 * set" (LBA48), in which case each of these byte-wide registers is 24 * actually a two-entry FIFO, and the "previous" byte pushed into the 25 * FIFO is used as the corresponding high-order byte. So, to set up 26 * the 48-bit address 0x123456abcdef, you would issue 27 * 28 * 0x56 -> LBA Low register 29 * 0xef -> LBA Low register 30 * 0x34 -> LBA Mid register 31 * 0xcd -> LBA Mid register 32 * 0x12 -> LBA High register 33 * 0xab -> LBA High register 34 * 35 * This structure encapsulates this information by providing a single 36 * 64-bit integer in native byte order, unioned with bytes named so 37 * that the sequence becomes 38 * 39 * low_prev -> LBA Low register 40 * low_cur -> LBA Low register 41 * mid_prev -> LBA Mid register 42 * mid_cur -> LBA Mid register 43 * high_prev -> LBA High register 44 * high_cur -> LBA High register 45 * 46 * Just to complicate matters further, in non-LBA48 mode it is 47 * possible to have a 28-bit address, in which case bits 27:24 must be 48 * written into the low four bits of the Device register. 49 */ 50 union ata_lba { 51 /** LBA as a 64-bit integer in native-endian order */ 52 uint64_t native; 53 /** ATA registers */ 54 struct { 55 #if __BYTE_ORDER == __LITTLE_ENDIAN 56 uint8_t low_cur; 57 uint8_t mid_cur; 58 uint8_t high_cur; 59 uint8_t low_prev; 60 uint8_t mid_prev; 61 uint8_t high_prev; 62 uint16_t pad; 63 #elif __BYTE_ORDER == __BIG_ENDIAN 64 uint16_t pad; 65 uint8_t high_prev; 66 uint8_t mid_prev; 67 uint8_t low_prev; 68 uint8_t high_cur; 69 uint8_t mid_cur; 70 uint8_t low_cur; 71 #else 72 #error "I need a byte order" 73 #endif 74 } bytes; 75 }; 76 77 /** An ATA 2-byte FIFO register */ 78 union ata_fifo { 79 /** Value in native-endian order */ 80 uint16_t native; 81 /** ATA registers */ 82 struct { 83 #if __BYTE_ORDER == __LITTLE_ENDIAN 84 uint8_t cur; 85 uint8_t prev; 86 #elif __BYTE_ORDER == __BIG_ENDIAN 87 uint8_t prev; 88 uint8_t cur; 89 #else 90 #error "I need a byte order" 91 #endif 92 } bytes; 93 }; 94 95 /** ATA command block */ 96 struct ata_cb { 97 /** Logical block address */ 98 union ata_lba lba; 99 /** Sector count */ 100 union ata_fifo count; 101 /** Error/feature register */ 102 union ata_fifo err_feat; 103 /** Device register */ 104 uint8_t device; 105 /** Command/status register */ 106 uint8_t cmd_stat; 107 /** LBA48 addressing flag */ 108 int lba48; 109 }; 110 111 /** Obsolete bits in the ATA device register */ 112 #define ATA_DEV_OBSOLETE 0xa0 113 114 /** LBA flag in the ATA device register */ 115 #define ATA_DEV_LBA 0x40 116 117 /** Slave ("device 1") flag in the ATA device register */ 118 #define ATA_DEV_SLAVE 0x10 119 120 /** Master ("device 0") flag in the ATA device register */ 121 #define ATA_DEV_MASTER 0x00 122 123 /** Mask of non-LBA portion of device register */ 124 #define ATA_DEV_MASK 0xf0 125 126 /** "Read sectors" command */ 127 #define ATA_CMD_READ 0x20 128 129 /** "Read sectors (ext)" command */ 130 #define ATA_CMD_READ_EXT 0x24 131 132 /** "Write sectors" command */ 133 #define ATA_CMD_WRITE 0x30 134 135 /** "Write sectors (ext)" command */ 136 #define ATA_CMD_WRITE_EXT 0x34 137 138 /** "Identify" command */ 139 #define ATA_CMD_IDENTIFY 0xec 140 141 /** An ATA command */ 142 struct ata_command { 143 /** ATA command block */ 144 struct ata_cb cb; 145 /** Data-out buffer (may be NULL) 146 * 147 * If non-NULL, this buffer must be ata_command::cb::count 148 * sectors in size. 149 */ 150 userptr_t data_out; 151 /** Data-in buffer (may be NULL) 152 * 153 * If non-NULL, this buffer must be ata_command::cb::count 154 * sectors in size. 155 */ 156 userptr_t data_in; 157 /** Command status code */ 158 int rc; 159 }; 160 161 /** 162 * Structure returned by ATA IDENTIFY command 163 * 164 * This is a huge structure with many fields that we don't care about, 165 * so we implement only a few fields. 166 */ 167 struct ata_identity { 168 uint16_t ignore_a[60]; /* words 0-59 */ 169 uint32_t lba_sectors; /* words 60-61 */ 170 uint16_t ignore_b[21]; /* words 62-82 */ 171 uint16_t supports_lba48; /* word 83 */ 172 uint16_t ignore_c[16]; /* words 84-99 */ 173 uint64_t lba48_sectors; /* words 100-103 */ 174 uint16_t ignore_d[152]; /* words 104-255 */ 175 }; 176 177 /** Supports LBA48 flag */ 178 #define ATA_SUPPORTS_LBA48 ( 1 << 10 ) 179 180 /** ATA sector size */ 181 #define ATA_SECTOR_SIZE 512 182 183 /** An ATA device */ 184 struct ata_device { 185 /** Block device interface */ 186 struct block_device blockdev; 187 /** Device number 188 * 189 * Must be ATA_DEV_MASTER or ATA_DEV_SLAVE. 190 */ 191 int device; 192 /** LBA48 extended addressing */ 193 int lba48; 194 /** 195 * Issue ATA command 196 * 197 * @v ata ATA device 198 * @v command ATA command 199 * @ret rc Return status code 200 */ 201 int ( * command ) ( struct ata_device *ata, 202 struct ata_command *command ); 203 /** Backing device */ 204 struct refcnt *backend; 205 }; 206 207 extern int init_atadev ( struct ata_device *ata ); 208 209 #endif /* _GPXE_ATA_H */ 210
