1 /* 2 * Copyright (C) 2011, 2012 The Android Open Source Project 3 * 4 * Licensed under the Apache License, Version 2.0 (the "License"); 5 * you may not use this file except in compliance with the License. 6 * You may obtain a copy of the License at 7 * 8 * http://www.apache.org/licenses/LICENSE-2.0 9 * 10 * Unless required by applicable law or agreed to in writing, software 11 * distributed under the License is distributed on an "AS IS" BASIS, 12 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. 13 * See the License for the specific language governing permissions and 14 * limitations under the License. 15 */ 16 17 #ifndef ANDROID_NFC_HAL_INTERFACE_H 18 #define ANDROID_NFC_HAL_INTERFACE_H 19 20 #include <stdint.h> 21 #include <strings.h> 22 #include <sys/cdefs.h> 23 #include <sys/types.h> 24 25 #include <hardware/hardware.h> 26 #include "nfc-base.h" 27 28 __BEGIN_DECLS 29 30 31 /* NFC device HAL for NCI-based NFC controllers. 32 * 33 * This HAL allows NCI silicon vendors to make use 34 * of the core NCI stack in Android for their own silicon. 35 * 36 * The responibilities of the NCI HAL implementation 37 * are as follows: 38 * 39 * - Implement the transport to the NFC controller 40 * - Implement each of the HAL methods specified below as applicable to their silicon 41 * - Pass up received NCI messages from the controller to the stack 42 * 43 * A simplified timeline of NCI HAL method calls: 44 * 1) Core NCI stack calls open() 45 * 2) Core NCI stack executes CORE_RESET and CORE_INIT through calls to write() 46 * 3) Core NCI stack calls core_initialized() to allow HAL to do post-init configuration 47 * 4) Core NCI stack calls pre_discover() to allow HAL to prepare for RF discovery 48 * 5) Core NCI stack starts discovery through calls to write() 49 * 6) Core NCI stack stops discovery through calls to write() (e.g. screen turns off) 50 * 7) Core NCI stack calls pre_discover() to prepare for RF discovery (e.g. screen turned back on) 51 * 8) Core NCI stack starts discovery through calls to write() 52 * ... 53 * ... 54 * 9) Core NCI stack calls close() 55 */ 56 #define NFC_NCI_HARDWARE_MODULE_ID "nfc_nci" 57 #define NFC_NCI_BCM2079X_HARDWARE_MODULE_ID "nfc_nci.bcm2079x" 58 #define NFC_NCI_CONTROLLER "nci" 59 60 /* 61 * nfc_nci_module_t should contain module-specific parameters 62 */ 63 typedef struct nfc_nci_module_t { 64 /** 65 * Common methods of the NFC NCI module. This *must* be the first member of 66 * nfc_nci_module_t as users of this structure will cast a hw_module_t to 67 * nfc_nci_module_t pointer in contexts where it's known the hw_module_t references a 68 * nfc_nci_module_t. 69 */ 70 struct hw_module_t common; 71 } nfc_nci_module_t; 72 73 typedef uint8_t nfc_event_t; 74 typedef uint8_t nfc_status_t; 75 76 /* 77 * The callback passed in from the NFC stack that the HAL 78 * can use to pass events back to the stack. 79 */ 80 typedef void (nfc_stack_callback_t) (nfc_event_t event, nfc_status_t event_status); 81 82 /* 83 * The callback passed in from the NFC stack that the HAL 84 * can use to pass incomming data to the stack. 85 */ 86 typedef void (nfc_stack_data_callback_t) (uint16_t data_len, uint8_t* p_data); 87 88 /* nfc_nci_device_t starts with a hw_device_t struct, 89 * followed by device-specific methods and members. 90 * 91 * All methods in the NCI HAL are asynchronous. 92 */ 93 typedef struct nfc_nci_device { 94 /** 95 * Common methods of the NFC NCI device. This *must* be the first member of 96 * nfc_nci_device_t as users of this structure will cast a hw_device_t to 97 * nfc_nci_device_t pointer in contexts where it's known the hw_device_t references a 98 * nfc_nci_device_t. 99 */ 100 struct hw_device_t common; 101 /* 102 * (*open)() Opens the NFC controller device and performs initialization. 103 * This may include patch download and other vendor-specific initialization. 104 * 105 * If open completes successfully, the controller should be ready to perform 106 * NCI initialization - ie accept CORE_RESET and subsequent commands through 107 * the write() call. 108 * 109 * If open() returns 0, the NCI stack will wait for a HAL_NFC_OPEN_CPLT_EVT 110 * before continuing. 111 * 112 * If open() returns any other value, the NCI stack will stop. 113 * 114 */ 115 int (*open)(const struct nfc_nci_device *p_dev, nfc_stack_callback_t *p_cback, 116 nfc_stack_data_callback_t *p_data_cback); 117 118 /* 119 * (*write)() Performs an NCI write. 120 * 121 * This method may queue writes and return immediately. The only 122 * requirement is that the writes are executed in order. 123 */ 124 int (*write)(const struct nfc_nci_device *p_dev, uint16_t data_len, const uint8_t *p_data); 125 126 /* 127 * (*core_initialized)() is called after the CORE_INIT_RSP is received from the NFCC. 128 * At this time, the HAL can do any chip-specific configuration. 129 * 130 * If core_initialized() returns 0, the NCI stack will wait for a HAL_NFC_POST_INIT_CPLT_EVT 131 * before continuing. 132 * 133 * If core_initialized() returns any other value, the NCI stack will continue 134 * immediately. 135 */ 136 int (*core_initialized)(const struct nfc_nci_device *p_dev, uint8_t* p_core_init_rsp_params); 137 138 /* 139 * (*pre_discover)() Is called every time before starting RF discovery. 140 * It is a good place to do vendor-specific configuration that must be 141 * performed every time RF discovery is about to be started. 142 * 143 * If pre_discover() returns 0, the NCI stack will wait for a HAL_NFC_PRE_DISCOVER_CPLT_EVT 144 * before continuing. 145 * 146 * If pre_discover() returns any other value, the NCI stack will start 147 * RF discovery immediately. 148 */ 149 int (*pre_discover)(const struct nfc_nci_device *p_dev); 150 151 /* 152 * (*close)() Closed the NFC controller. Should free all resources. 153 */ 154 int (*close)(const struct nfc_nci_device *p_dev); 155 156 /* 157 * (*control_granted)() Grant HAL the exclusive control to send NCI commands. 158 * Called in response to HAL_REQUEST_CONTROL_EVT. 159 * Must only be called when there are no NCI commands pending. 160 * HAL_RELEASE_CONTROL_EVT will notify when HAL no longer needs exclusive control. 161 */ 162 int (*control_granted)(const struct nfc_nci_device *p_dev); 163 164 /* 165 * (*power_cycle)() Restart controller by power cyle; 166 * HAL_OPEN_CPLT_EVT will notify when operation is complete. 167 */ 168 int (*power_cycle)(const struct nfc_nci_device *p_dev); 169 } nfc_nci_device_t; 170 171 /* 172 * Convenience methods that the NFC stack can use to open 173 * and close an NCI device 174 */ 175 static inline int nfc_nci_open(const struct hw_module_t* module, 176 nfc_nci_device_t** dev) { 177 return module->methods->open(module, NFC_NCI_CONTROLLER, 178 (struct hw_device_t**) dev); 179 } 180 181 static inline int nfc_nci_close(nfc_nci_device_t* dev) { 182 return dev->common.close(&dev->common); 183 } 184 /* 185 * End NFC NCI HAL 186 */ 187 188 /* 189 * This is a limited NFC HAL for NXP PN544-based devices. 190 * This HAL as Android is moving to 191 * an NCI-based NFC stack. 192 * 193 * All NCI-based NFC controllers should use the NFC-NCI 194 * HAL instead. 195 * Begin PN544 specific HAL 196 */ 197 #define NFC_HARDWARE_MODULE_ID "nfc" 198 199 #define NFC_PN544_CONTROLLER "pn544" 200 201 typedef struct nfc_module_t { 202 /** 203 * Common methods of the NFC NXP PN544 module. This *must* be the first member of 204 * nfc_module_t as users of this structure will cast a hw_module_t to 205 * nfc_module_t pointer in contexts where it's known the hw_module_t references a 206 * nfc_module_t. 207 */ 208 struct hw_module_t common; 209 } nfc_module_t; 210 211 /* 212 * PN544 linktypes. 213 * UART 214 * I2C 215 * USB (uses UART DAL) 216 */ 217 typedef enum { 218 PN544_LINK_TYPE_UART, 219 PN544_LINK_TYPE_I2C, 220 PN544_LINK_TYPE_USB, 221 PN544_LINK_TYPE_INVALID, 222 } nfc_pn544_linktype; 223 224 typedef struct { 225 /** 226 * Common methods of the NFC NXP PN544 device. This *must* be the first member of 227 * nfc_pn544_device_t as users of this structure will cast a hw_device_t to 228 * nfc_pn544_device_t pointer in contexts where it's known the hw_device_t references a 229 * nfc_pn544_device_t. 230 */ 231 struct hw_device_t common; 232 233 /* The number of EEPROM registers to write */ 234 uint32_t num_eeprom_settings; 235 236 /* The actual EEPROM settings 237 * For PN544, each EEPROM setting is a 4-byte entry, 238 * of the format [0x00, addr_msb, addr_lsb, value]. 239 */ 240 uint8_t* eeprom_settings; 241 242 /* The link type to which the PN544 is connected */ 243 nfc_pn544_linktype linktype; 244 245 /* The device node to which the PN544 is connected */ 246 const char* device_node; 247 248 /* On Crespo we had an I2C issue that would cause us to sometimes read 249 * the I2C slave address (0x57) over the bus. libnfc contains 250 * a hack to ignore this byte and try to read the length byte 251 * again. 252 * Set to 0 to disable the workaround, 1 to enable it. 253 */ 254 uint8_t enable_i2c_workaround; 255 /* I2C slave address. Multiple I2C addresses are 256 * possible for PN544 module. Configure address according to 257 * board design. 258 */ 259 uint8_t i2c_device_address; 260 } nfc_pn544_device_t; 261 262 static inline int nfc_pn544_open(const struct hw_module_t* module, 263 nfc_pn544_device_t** dev) { 264 return module->methods->open(module, NFC_PN544_CONTROLLER, 265 (struct hw_device_t**) dev); 266 } 267 268 static inline int nfc_pn544_close(nfc_pn544_device_t* dev) { 269 return dev->common.close(&dev->common); 270 } 271 /* 272 * End PN544 specific HAL 273 */ 274 275 __END_DECLS 276 277 #endif // ANDROID_NFC_HAL_INTERFACE_H 278