1 # SPDX-License-Identifier: GPL-2.0+ 2 # 3 # (C) Copyright 2009 4 # Marvell Semiconductor <www.marvell.com> 5 # Written-by: Prafulla Wadaskar <prafulla (a] marvell.com> 6 # Refer to doc/README.kwbimage for more details about how-to 7 # configure and create kirkwood boot images. 8 # 9 10 # Boot Media configurations 11 BOOT_FROM nand 12 NAND_ECC_MODE default 13 NAND_PAGE_SIZE 0x0800 14 15 # SOC registers configuration using bootrom header extension 16 # Maximum KWBIMAGE_MAX_CONFIG configurations allowed 17 18 # Configure RGMII-0 interface pad voltage to 1.8V 19 DATA 0xFFD100e0 0x1b1b1b9b 20 21 #Dram initalization for SINGLE x16 CL=5 @ 400MHz 22 DATA 0xFFD01400 0x43000c30 # DDR Configuration register 23 # bit13-0: 0xc30 (3120 DDR2 clks refresh rate) 24 # bit23-14: zero 25 # bit24: 1= enable exit self refresh mode on DDR access 26 # bit25: 1 required 27 # bit29-26: zero 28 # bit31-30: 01 29 30 DATA 0xFFD01404 0x37543000 # DDR Controller Control Low 31 # bit 4: 0=addr/cmd in smame cycle 32 # bit 5: 0=clk is driven during self refresh, we don't care for APX 33 # bit 6: 0=use recommended falling edge of clk for addr/cmd 34 # bit14: 0=input buffer always powered up 35 # bit18: 1=cpu lock transaction enabled 36 # bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 37 # bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM 38 # bit30-28: 3 required 39 # bit31: 0=no additional STARTBURST delay 40 41 DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1) 42 # bit3-0: TRAS lsbs 43 # bit7-4: TRCD 44 # bit11- 8: TRP 45 # bit15-12: TWR 46 # bit19-16: TWTR 47 # bit20: TRAS msb 48 # bit23-21: 0x0 49 # bit27-24: TRRD 50 # bit31-28: TRTP 51 52 DATA 0xFFD0140C 0x00000a33 # DDR Timing (High) 53 # bit6-0: TRFC 54 # bit8-7: TR2R 55 # bit10-9: TR2W 56 # bit12-11: TW2W 57 # bit31-13: zero required 58 59 DATA 0xFFD01410 0x000000cc # DDR Address Control 60 # bit1-0: 00, Cs0width=x8 61 # bit3-2: 11, Cs0size=1Gb 62 # bit5-4: 00, Cs1width=x8 63 # bit7-6: 11, Cs1size=1Gb 64 # bit9-8: 00, Cs2width=nonexistent 65 # bit11-10: 00, Cs2size =nonexistent 66 # bit13-12: 00, Cs3width=nonexistent 67 # bit15-14: 00, Cs3size =nonexistent 68 # bit16: 0, Cs0AddrSel 69 # bit17: 0, Cs1AddrSel 70 # bit18: 0, Cs2AddrSel 71 # bit19: 0, Cs3AddrSel 72 # bit31-20: 0 required 73 74 DATA 0xFFD01414 0x00000000 # DDR Open Pages Control 75 # bit0: 0, OpenPage enabled 76 # bit31-1: 0 required 77 78 DATA 0xFFD01418 0x00000000 # DDR Operation 79 # bit3-0: 0x0, DDR cmd 80 # bit31-4: 0 required 81 82 DATA 0xFFD0141C 0x00000C52 # DDR Mode 83 # bit2-0: 2, BurstLen=2 required 84 # bit3: 0, BurstType=0 required 85 # bit6-4: 4, CL=5 86 # bit7: 0, TestMode=0 normal 87 # bit8: 0, DLL reset=0 normal 88 # bit11-9: 6, auto-precharge write recovery ???????????? 89 # bit12: 0, PD must be zero 90 # bit31-13: 0 required 91 92 DATA 0xFFD01420 0x00000040 # DDR Extended Mode 93 # bit0: 0, DDR DLL enabled 94 # bit1: 0, DDR drive strenght normal 95 # bit2: 0, DDR ODT control lsd (disabled) 96 # bit5-3: 000, required 97 # bit6: 1, DDR ODT control msb, (disabled) 98 # bit9-7: 000, required 99 # bit10: 0, differential DQS enabled 100 # bit11: 0, required 101 # bit12: 0, DDR output buffer enabled 102 # bit31-13: 0 required 103 104 DATA 0xFFD01424 0x0000F17F # DDR Controller Control High 105 # bit2-0: 111, required 106 # bit3 : 1 , MBUS Burst Chop disabled 107 # bit6-4: 111, required 108 # bit7 : 0 109 # bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz 110 # bit9 : 0 , no half clock cycle addition to dataout 111 # bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals 112 # bit11 : 0 , 1/4 clock cycle skew disabled for write mesh 113 # bit15-12: 1111 required 114 # bit31-16: 0 required 115 116 DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) 117 DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) 118 119 DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 120 DATA 0xFFD01504 0x0FFFFFF1 # CS[0]n Size 121 # bit0: 1, Window enabled 122 # bit1: 0, Write Protect disabled 123 # bit3-2: 00, CS0 hit selected 124 # bit23-4: ones, required 125 # bit31-24: 0x0F, Size (i.e. 256MB) 126 127 DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb 128 DATA 0xFFD0150C 0x0FFFFFF5 # CS[1]n Size 256Mb Window enabled for CS1 129 130 DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled 131 DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled 132 133 DATA 0xFFD01494 0x00030000 # DDR ODT Control (Low) 134 DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) 135 # bit1-0: 00, ODT0 controlled by ODT Control (low) register above 136 # bit3-2: 01, ODT1 active NEVER! 137 # bit31-4: zero, required 138 139 DATA 0xFFD0149C 0x0000E803 # CPU ODT Control 140 DATA 0xFFD01480 0x00000001 # DDR Initialization Control 141 #bit0=1, enable DDR init upon this register write 142 143 # End of Header extension 144 DATA 0x0 0x0 145
