1 Overview 2 -------- 3 QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance 4 development platform, with a complete debugging environment. 5 The LS1012ARDB board supports the QorIQ LS1012A processor and is 6 optimized to support the high-bandwidth DDR3L memory and 7 a full complement of high-speed SerDes ports. 8 9 LS1012A SoC Overview 10 -------------------- 11 Please refer arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc for LS2080A 12 SoC overview. 13 14 LS1012ARDB board Overview 15 ----------------------- 16 - SERDES Connections, 4 lanes supporting: 17 - PCI Express - 3.0 18 - SGMII, SGMII 2.5 19 - SATA 3.0 20 - DDR Controller 21 - 16-bit, 1 GB DDR3L SDRAM memory, running at data rates up to 1 GT/s 22 -QSPI: A dual 1:3 switch, NX3L4357GM,115 (U35) drives the QSPI chip-select 23 signals to 24 - QSPI NOR flash memory (2 virtual banks) 25 - the QSPI emulator.s 26 - USB 3.0 27 - one high-speed USB 2.0/3.0 port. 28 - Two enhanced secure digital host controllers: 29 - SDHC1 controller can be connected to onboard SDHC connector 30 - SDHC2 controller: Three dual 1:4 mux/demux devices, 31 74CBTLV3253DS (U30, U31, U33) drive the SDHC2 signals to eMMC, 32 SDIO WiFi, SPI, and Ardiuno shield 33 - 2 I2C controllers 34 - One SATA onboard connectors 35 - UART 36 - The LS1012A processor consists of two UART controllers, 37 out of which only UART1 is used on RDB. 38 - ARM JTAG support 39 40 Booting Options 41 --------------- 42 a) QSPI Flash Emu Boot 43 b) QSPI Flash 1 44 c) QSPI Flash 2 45 46 QSPI flash map 47 -------------- 48 Images | Size |QSPI Flash Address 49 ------------------------------------------ 50 RCW + PBI | 1MB | 0x4000_0000 51 U-boot | 1MB | 0x4010_0000 52 U-boot Env | 1MB | 0x4020_0000 53 PPA FIT image | 2MB | 0x4050_0000 54 Linux ITB | ~53MB | 0x40A0_0000 55 56 LS1012A2G5RDB board Overview 57 ----------------------- 58 - SERDES Connections, 3 lanes supporting: 59 - SGMII, SGMII 2.5 60 - SATA 3.0 61 - DDR Controller 62 - 16-bit, 1 GB DDR3L SDRAM memory, running at data rates up to 1 GT/s 63 -QSPI: A dual 1:3 switch, NX3L4357GM,115 (U35) drives the QSPI chip-select 64 signals to 65 - QSPI NOR flash memory 66 - USB 3.0 67 - one high-speed USB 2.0/3.0 port. 68 - SDIO WiFi, SPI 69 - 2 I2C controllers 70 - One SATA onboard connectors 71 - UART 72 - The LS1012A processor consists of two UART controllers, 73 out of which only UART1 is used on 2G5RDB. 74 - ARM JTAG support 75 76 Major Difference between LS1012ARDB and LS1012A-2G5RDB 77 ------------------------------------------------------ 78 1. LS1012A-2G5RDB has Type C USB connector unlike USB Type A/B of LS1012ARDB 79 2. LS1012A-2G5RDB has 2 2.5G AQR PHY unlike 2 1G Realtek RTL8211FS PHYs 80 of LS1012ARDB 81 3. LS1012A-2G5RDB is not having Arduino header 82 4. LS1012A-2G5RDB doesn't have PCI slot 83 84 Booting Options 85 --------------- 86 QSPI Flash 87 88 QSPI flash map 89 -------------- 90 Images | Size |QSPI Flash Address 91 ------------------------------------------ 92 RCW + PBI | 1MB | 0x4000_0000 93 U-boot | 1MB | 0x4010_0000 94 U-boot Env | 1MB | 0x4030_0000 95 PPA FIT image | 2MB | 0x4040_0000 96 PFE firmware | 20K | 0x00a0_0000 97 Linux ITB | ~53MB | 0x4100_0000 98
