1 ## Hardware assembly ## 2 Depending on your specific needs, you may want to introduce some variations. 3 In most cases it's possible to assemble a device with partial functionality (e.g. only for audio latency) on a solderless breadboard. 4 5 ### List of suggested parts ### 6 7 * USB OTG cable like 8 [this](http://www.amazon.com/Generic-Micro-Cable-Cellphone-Tablet/dp/B00AYPEL56) 9 (or a USB Type-C to A adapter) 10 for connecting WALT to your phone or tablet 11 * Microcontroller board - [Teensy LC](https://www.pjrc.com/teensy/teensyLC.html) 12 * Photodiodes - [BPW34](http://www.digikey.com/product-detail/en/osram-opto-semiconductors-inc/BPW34/475-1070-ND/607274) (3 units) 13 * Laser - any laser pointer will do, ~1 mW is just fine (5 mW is ok, but avoid stronger ones) 14 * Accelerometer board [Adafruit ADXL335](https://www.adafruit.com/product/163) **with filter capacitors removed**. 15 It's very important to remove the filter capacitors, otherwise they smooth out the abrupt shock we are looking for. 16 Alternatively use the ADXL335 chip directly without the breakout board, but it's rather difficult to solder manually. 17 * Some resistors and capacitors - see schematics 18 * TRRS connector or wire for audio measurements 19 * Clipboard, like [this one](https://upload.wikimedia.org/wikipedia/commons/c/c0/Wood-clipboard.jpg) 20 21 ### Schematic ### 22 The current hardware version we use (r0.7) can be found as KiCAD project in this directory. 23 * [PDF](WALT_schematic.pdf) 24 * Blank PCBs can be ordered directly via [this shared project on OSH Park](https://oshpark.com/shared_projects/M5Z8fYCX) 25 * List of parts for version r0.7 - [BOM as a tsv file](WALT_bom_r07.tsv) 26 27  28 29 30 ### Microcontroller code ### 31 32 Important pin numbers from the code listed below, defined in [walt.ino](../arduino/walt/walt.ino) 33 34 * PD_LASER_PIN 14 - Photodiode that looks at the laser 35 * G_PIN 15 // Same as A1 - Accelerometer for detecting when touch probe hits the screen 36 * PD_SCREEN_PIN 20 // Same as A6 - Photodiode that looks at the screen 37 * AUDIO_PIN 22 // Same as A8 - Detects audio signal from headphones output 38 * MIC_PIN 23 // Same as A9 - uses PWM to generate a tone for measuring microphone latency. 39 40 ### Schematic - older version ### 41 An older version can be found 42 [here on Upverter](https://upverter.com/kamrik/8af1f3b04e47ab78/WALT_w_audio/) 43 44  45 46 47 ### More electronics notes ### 48 49 * If using Teensy 3.1 instead of LC, it wont be able to directly read 50 the screen photodiodes - a buffer opamp will be needed. The screen photodiodes 51 are bundled as a couple to produce more current, a single photodiode with 1.5M 52 resistor should provide the same result, but might be at the limit of what the 53 teensy can measure (input impedance), and again, an opamp will be needed. 54 * BPW34 photodiode has a small protrusion on the cathode pin (cathode marker). 55 Anode has a white dot near it. 56 * Note the different setup of the laser and screen photodiode. The laser one 57 uses internal pullup resistor (about 20k), enabled by pinMode(PD_LASER_PIN, 58 INPUT_PULLUP); 59 60 ## Mechanical ## 61 62 Enclosure must be made from a non conductive and non transparent material. 63 64 * The enclosure used for r0.7 production run is available in this repo as [STL](enclosure/WALT_recessed_enclosure.stl) and [STEP](enclosure/WALT_recessed_enclosure.step) files. It also used four M3x6 screws (McMaster-Carr PN 92000A116) and M3 hex nuts (McMaster-Carr PN 91828A211) 65 * A slightly simpler enclosure suitable for printing on a desktop 3D printer is available as a [public OnShape project](https://cad.onshape.com/documents/6410a1ac7964cb29c4a5ba41/v/32bc78539f48ab7f514eeb31/e/fa513fcc84a825e97020c8b3) and [STL](enclosure/WALT_3DP_enclosure_v7.stl) file 66 * A minimal enclosure suitable for 2D cutting from any 5 to 8 mm thick substrate is available as a [public OnShape project](https://cad.onshape.com/documents/5d7f21c8877ea8961bc499ef/v/84a66f3baf5f4a8f41be3bd7/e/e2a23559efbeb63be3916123) 67
