1 /* 2 * Copyright (c) 1993 Herb Peyerl (hpeyerl (at) novatel.ca) All rights reserved. 3 * 4 * Redistribution and use in source and binary forms, with or without 5 * modification, are permitted provided that the following conditions are 6 * met: 1. Redistributions of source code must retain the above copyright 7 * notice, this list of conditions and the following disclaimer. 2. The name 8 * of the author may not be used to endorse or promote products derived from 9 * this software withough specific prior written permission 10 * 11 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR IMPLIED 12 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF 13 * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO 14 * EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, 15 * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED 16 * TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR 17 * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF 18 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING 19 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS 20 * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 21 * 22 * if_epreg.h,v 1.4 1994/11/13 10:12:37 gibbs Exp Modified by: 23 * 24 October 2, 1994 25 26 Modified by: Andres Vega Garcia 27 28 INRIA - Sophia Antipolis, France 29 e-mail: avega (at) sophia.inria.fr 30 finger: avega (at) pax.inria.fr 31 32 */ 33 34 /* 35 * Ethernet software status per interface. 36 */ 37 /* 38 * Some global constants 39 */ 40 41 #define TX_INIT_RATE 16 42 #define TX_INIT_MAX_RATE 64 43 #define RX_INIT_LATENCY 64 44 #define RX_INIT_EARLY_THRESH 64 45 #define MIN_RX_EARLY_THRESHF 16 /* not less than ether_header */ 46 #define MIN_RX_EARLY_THRESHL 4 47 48 #define EEPROMSIZE 0x40 49 #define MAX_EEPROMBUSY 1000 50 #define EP_LAST_TAG 0xd7 51 #define EP_MAX_BOARDS 16 52 #define EP_ID_PORT 0x100 53 54 /* 55 * some macros to acces long named fields 56 */ 57 #define IS_BASE (eth_nic_base) 58 #define BASE (eth_nic_base) 59 60 /* 61 * Commands to read/write EEPROM trough EEPROM command register (Window 0, 62 * Offset 0xa) 63 */ 64 #define EEPROM_CMD_RD 0x0080 /* Read: Address required (5 bits) */ 65 #define EEPROM_CMD_WR 0x0040 /* Write: Address required (5 bits) */ 66 #define EEPROM_CMD_ERASE 0x00c0 /* Erase: Address required (5 bits) */ 67 #define EEPROM_CMD_EWEN 0x0030 /* Erase/Write Enable: No data required */ 68 69 #define EEPROM_BUSY (1<<15) 70 #define EEPROM_TST_MODE (1<<14) 71 72 /* 73 * Some short functions, worth to let them be a macro 74 */ 75 #define is_eeprom_busy(b) (inw((b)+EP_W0_EEPROM_COMMAND)&EEPROM_BUSY) 76 #define GO_WINDOW(x) outw(WINDOW_SELECT|(x), BASE+EP_COMMAND) 77 78 /************************************************************************** 79 * 80 * These define the EEPROM data structure. They are used in the probe 81 * function to verify the existance of the adapter after having sent 82 * the ID_Sequence. 83 * 84 * There are others but only the ones we use are defined here. 85 * 86 **************************************************************************/ 87 88 #define EEPROM_NODE_ADDR_0 0x0 /* Word */ 89 #define EEPROM_NODE_ADDR_1 0x1 /* Word */ 90 #define EEPROM_NODE_ADDR_2 0x2 /* Word */ 91 #define EEPROM_PROD_ID 0x3 /* 0x9[0-f]50 */ 92 #define EEPROM_MFG_ID 0x7 /* 0x6d50 */ 93 #define EEPROM_ADDR_CFG 0x8 /* Base addr */ 94 #define EEPROM_RESOURCE_CFG 0x9 /* IRQ. Bits 12-15 */ 95 96 /************************************************************************** 97 * 98 * These are the registers for the 3Com 3c509 and their bit patterns when 99 * applicable. They have been taken out the the "EtherLink III Parallel 100 * Tasking EISA and ISA Technical Reference" "Beta Draft 10/30/92" manual 101 * from 3com. 102 * 103 **************************************************************************/ 104 105 #define EP_COMMAND 0x0e /* Write. BASE+0x0e is always a 106 * command reg. */ 107 #define EP_STATUS 0x0e /* Read. BASE+0x0e is always status 108 * reg. */ 109 #define EP_WINDOW 0x0f /* Read. BASE+0x0f is always window 110 * reg. */ 111 /* 112 * Window 0 registers. Setup. 113 */ 114 /* Write */ 115 #define EP_W0_EEPROM_DATA 0x0c 116 #define EP_W0_EEPROM_COMMAND 0x0a 117 #define EP_W0_RESOURCE_CFG 0x08 118 #define EP_W0_ADDRESS_CFG 0x06 119 #define EP_W0_CONFIG_CTRL 0x04 120 /* Read */ 121 #define EP_W0_PRODUCT_ID 0x02 122 #define EP_W0_MFG_ID 0x00 123 124 /* 125 * Window 1 registers. Operating Set. 126 */ 127 /* Write */ 128 #define EP_W1_TX_PIO_WR_2 0x02 129 #define EP_W1_TX_PIO_WR_1 0x00 130 /* Read */ 131 #define EP_W1_FREE_TX 0x0c 132 #define EP_W1_TX_STATUS 0x0b /* byte */ 133 #define EP_W1_TIMER 0x0a /* byte */ 134 #define EP_W1_RX_STATUS 0x08 135 #define EP_W1_RX_PIO_RD_2 0x02 136 #define EP_W1_RX_PIO_RD_1 0x00 137 138 /* 139 * Window 2 registers. Station Address Setup/Read 140 */ 141 /* Read/Write */ 142 #define EP_W2_ADDR_5 0x05 143 #define EP_W2_ADDR_4 0x04 144 #define EP_W2_ADDR_3 0x03 145 #define EP_W2_ADDR_2 0x02 146 #define EP_W2_ADDR_1 0x01 147 #define EP_W2_ADDR_0 0x00 148 149 /* 150 * Window 3 registers. FIFO Management. 151 */ 152 /* Read */ 153 #define EP_W3_FREE_TX 0x0c 154 #define EP_W3_FREE_RX 0x0a 155 156 /* 157 * Window 4 registers. Diagnostics. 158 */ 159 /* Read/Write */ 160 #define EP_W4_MEDIA_TYPE 0x0a 161 #define EP_W4_CTRLR_STATUS 0x08 162 #define EP_W4_NET_DIAG 0x06 163 #define EP_W4_FIFO_DIAG 0x04 164 #define EP_W4_HOST_DIAG 0x02 165 #define EP_W4_TX_DIAG 0x00 166 167 /* 168 * Window 5 Registers. Results and Internal status. 169 */ 170 /* Read */ 171 #define EP_W5_READ_0_MASK 0x0c 172 #define EP_W5_INTR_MASK 0x0a 173 #define EP_W5_RX_FILTER 0x08 174 #define EP_W5_RX_EARLY_THRESH 0x06 175 #define EP_W5_TX_AVAIL_THRESH 0x02 176 #define EP_W5_TX_START_THRESH 0x00 177 178 /* 179 * Window 6 registers. Statistics. 180 */ 181 /* Read/Write */ 182 #define TX_TOTAL_OK 0x0c 183 #define RX_TOTAL_OK 0x0a 184 #define TX_DEFERRALS 0x08 185 #define RX_FRAMES_OK 0x07 186 #define TX_FRAMES_OK 0x06 187 #define RX_OVERRUNS 0x05 188 #define TX_COLLISIONS 0x04 189 #define TX_AFTER_1_COLLISION 0x03 190 #define TX_AFTER_X_COLLISIONS 0x02 191 #define TX_NO_SQE 0x01 192 #define TX_CD_LOST 0x00 193 194 /**************************************** 195 * 196 * Register definitions. 197 * 198 ****************************************/ 199 200 /* 201 * Command register. All windows. 202 * 203 * 16 bit register. 204 * 15-11: 5-bit code for command to be executed. 205 * 10-0: 11-bit arg if any. For commands with no args; 206 * this can be set to anything. 207 */ 208 #define GLOBAL_RESET (unsigned short) 0x0000 /* Wait at least 1ms 209 * after issuing */ 210 #define WINDOW_SELECT (unsigned short) (0x1<<11) 211 #define START_TRANSCEIVER (unsigned short) (0x2<<11) /* Read ADDR_CFG reg to 212 * determine whether 213 * this is needed. If 214 * so; wait 800 uSec 215 * before using trans- 216 * ceiver. */ 217 #define RX_DISABLE (unsigned short) (0x3<<11) /* state disabled on 218 * power-up */ 219 #define RX_ENABLE (unsigned short) (0x4<<11) 220 #define RX_RESET (unsigned short) (0x5<<11) 221 #define RX_DISCARD_TOP_PACK (unsigned short) (0x8<<11) 222 #define TX_ENABLE (unsigned short) (0x9<<11) 223 #define TX_DISABLE (unsigned short) (0xa<<11) 224 #define TX_RESET (unsigned short) (0xb<<11) 225 #define REQ_INTR (unsigned short) (0xc<<11) 226 #define SET_INTR_MASK (unsigned short) (0xe<<11) 227 #define SET_RD_0_MASK (unsigned short) (0xf<<11) 228 #define SET_RX_FILTER (unsigned short) (0x10<<11) 229 #define FIL_INDIVIDUAL (unsigned short) (0x1) 230 #define FIL_GROUP (unsigned short) (0x2) 231 #define FIL_BRDCST (unsigned short) (0x4) 232 #define FIL_ALL (unsigned short) (0x8) 233 #define SET_RX_EARLY_THRESH (unsigned short) (0x11<<11) 234 #define SET_TX_AVAIL_THRESH (unsigned short) (0x12<<11) 235 #define SET_TX_START_THRESH (unsigned short) (0x13<<11) 236 #define STATS_ENABLE (unsigned short) (0x15<<11) 237 #define STATS_DISABLE (unsigned short) (0x16<<11) 238 #define STOP_TRANSCEIVER (unsigned short) (0x17<<11) 239 /* 240 * The following C_* acknowledge the various interrupts. Some of them don't 241 * do anything. See the manual. 242 */ 243 #define ACK_INTR (unsigned short) (0x6800) 244 #define C_INTR_LATCH (unsigned short) (ACK_INTR|0x1) 245 #define C_CARD_FAILURE (unsigned short) (ACK_INTR|0x2) 246 #define C_TX_COMPLETE (unsigned short) (ACK_INTR|0x4) 247 #define C_TX_AVAIL (unsigned short) (ACK_INTR|0x8) 248 #define C_RX_COMPLETE (unsigned short) (ACK_INTR|0x10) 249 #define C_RX_EARLY (unsigned short) (ACK_INTR|0x20) 250 #define C_INT_RQD (unsigned short) (ACK_INTR|0x40) 251 #define C_UPD_STATS (unsigned short) (ACK_INTR|0x80) 252 253 /* 254 * Status register. All windows. 255 * 256 * 15-13: Window number(0-7). 257 * 12: Command_in_progress. 258 * 11: reserved. 259 * 10: reserved. 260 * 9: reserved. 261 * 8: reserved. 262 * 7: Update Statistics. 263 * 6: Interrupt Requested. 264 * 5: RX Early. 265 * 4: RX Complete. 266 * 3: TX Available. 267 * 2: TX Complete. 268 * 1: Adapter Failure. 269 * 0: Interrupt Latch. 270 */ 271 #define S_INTR_LATCH (unsigned short) (0x1) 272 #define S_CARD_FAILURE (unsigned short) (0x2) 273 #define S_TX_COMPLETE (unsigned short) (0x4) 274 #define S_TX_AVAIL (unsigned short) (0x8) 275 #define S_RX_COMPLETE (unsigned short) (0x10) 276 #define S_RX_EARLY (unsigned short) (0x20) 277 #define S_INT_RQD (unsigned short) (0x40) 278 #define S_UPD_STATS (unsigned short) (0x80) 279 #define S_5_INTS (S_CARD_FAILURE|S_TX_COMPLETE|\ 280 S_TX_AVAIL|S_RX_COMPLETE|S_RX_EARLY) 281 #define S_COMMAND_IN_PROGRESS (unsigned short) (0x1000) 282 283 /* 284 * FIFO Registers. 285 * RX Status. Window 1/Port 08 286 * 287 * 15: Incomplete or FIFO empty. 288 * 14: 1: Error in RX Packet 0: Incomplete or no error. 289 * 13-11: Type of error. 290 * 1000 = Overrun. 291 * 1011 = Run Packet Error. 292 * 1100 = Alignment Error. 293 * 1101 = CRC Error. 294 * 1001 = Oversize Packet Error (>1514 bytes) 295 * 0010 = Dribble Bits. 296 * (all other error codes, no errors.) 297 * 298 * 10-0: RX Bytes (0-1514) 299 */ 300 #define ERR_RX_INCOMPLETE (unsigned short) (0x1<<15) 301 #define ERR_RX (unsigned short) (0x1<<14) 302 #define ERR_RX_OVERRUN (unsigned short) (0x8<<11) 303 #define ERR_RX_RUN_PKT (unsigned short) (0xb<<11) 304 #define ERR_RX_ALIGN (unsigned short) (0xc<<11) 305 #define ERR_RX_CRC (unsigned short) (0xd<<11) 306 #define ERR_RX_OVERSIZE (unsigned short) (0x9<<11) 307 #define ERR_RX_DRIBBLE (unsigned short) (0x2<<11) 308 309 /* 310 * FIFO Registers. 311 * TX Status. Window 1/Port 0B 312 * 313 * Reports the transmit status of a completed transmission. Writing this 314 * register pops the transmit completion stack. 315 * 316 * Window 1/Port 0x0b. 317 * 318 * 7: Complete 319 * 6: Interrupt on successful transmission requested. 320 * 5: Jabber Error (TP Only, TX Reset required. ) 321 * 4: Underrun (TX Reset required. ) 322 * 3: Maximum Collisions. 323 * 2: TX Status Overflow. 324 * 1-0: Undefined. 325 * 326 */ 327 #define TXS_COMPLETE 0x80 328 #define TXS_SUCCES_INTR_REQ 0x40 329 #define TXS_JABBER 0x20 330 #define TXS_UNDERRUN 0x10 331 #define TXS_MAX_COLLISION 0x8 332 #define TXS_STATUS_OVERFLOW 0x4 333 334 /* 335 * Configuration control register. 336 * Window 0/Port 04 337 */ 338 /* Read */ 339 #define IS_AUI (1<<13) 340 #define IS_BNC (1<<12) 341 #define IS_UTP (1<<9) 342 /* Write */ 343 #define ENABLE_DRQ_IRQ 0x0001 344 #define W0_P4_CMD_RESET_ADAPTER 0x4 345 #define W0_P4_CMD_ENABLE_ADAPTER 0x1 346 /* 347 * Media type and status. 348 * Window 4/Port 0A 349 */ 350 #define ENABLE_UTP 0xc0 351 #define DISABLE_UTP 0x0 352 353 /* 354 * Resource control register 355 */ 356 357 #define SET_IRQ(i) ( ((i)<<12) | 0xF00) /* set IRQ i */ 358 359 /* 360 * Receive status register 361 */ 362 363 #define RX_BYTES_MASK (unsigned short) (0x07ff) 364 #define RX_ERROR 0x4000 365 #define RX_INCOMPLETE 0x8000 366 367 368 /* 369 * Misc defines for various things. 370 */ 371 #define ACTIVATE_ADAPTER_TO_CONFIG 0xff /* to the id_port */ 372 #define MFG_ID 0x6d50 /* in EEPROM and W0 ADDR_CONFIG */ 373 #define PROD_ID 0x9150 374 375 #define AUI 0x1 376 #define BNC 0x2 377 #define UTP 0x4 378 379 #define RX_BYTES_MASK (unsigned short) (0x07ff) 380 381 /* EISA support */ 382 #define EP_EISA_START 0x1000 383 #define EP_EISA_W0 0x0c80 384 385 #ifdef INCLUDE_3C529 386 /* MCA support */ 387 #define MCA_MOTHERBOARD_SETUP_REG 0x94 388 #define MCA_ADAPTER_SETUP_REG 0x96 389 #define MCA_MAX_SLOT_NR 8 390 #define MCA_POS_REG(n) (0x100+(n)) 391 #endif 392 393 /* 394 * Local variables: 395 * c-basic-offset: 8 396 * End: 397 */ 398
