1 The rate estimator can match on estimated rates as collected by the RATEEST 2 target. It supports matching on absolute bps/pps values, comparing two rate 3 estimators and matching on the difference between two rate estimators. 4 .PP 5 For a better understanding of the available options, these are all possible 6 combinations: 7 .\" * Absolute: 8 .IP \(bu 4 9 \fBrateest\fP \fIoperator\fP \fBrateest-bps\fP 10 .IP \(bu 4 11 \fBrateest\fP \fIoperator\fP \fBrateest-pps\fP 12 .\" * Absolute + Delta: 13 .IP \(bu 4 14 (\fBrateest\fP minus \fBrateest-bps1\fP) \fIoperator\fP \fBrateest-bps2\fP 15 .IP \(bu 4 16 (\fBrateest\fP minus \fBrateest-pps1\fP) \fIoperator\fP \fBrateest-pps2\fP 17 .\" * Relative: 18 .IP \(bu 4 19 \fBrateest1\fP \fIoperator\fP \fBrateest2\fP \fBrateest-bps\fP(without rate!) 20 .IP \(bu 4 21 \fBrateest1\fP \fIoperator\fP \fBrateest2\fP \fBrateest-pps\fP(without rate!) 22 .\" * Relative + Delta: 23 .IP \(bu 4 24 (\fBrateest1\fP minus \fBrateest-bps1\fP) \fIoperator\fP 25 (\fBrateest2\fP minus \fBrateest-bps2\fP) 26 .IP \(bu 4 27 (\fBrateest1\fP minus \fBrateest-pps1\fP) \fIoperator\fP 28 (\fBrateest2\fP minus \fBrateest-pps2\fP) 29 .TP 30 \fB\-\-rateest\-delta\fP 31 For each estimator (either absolute or relative mode), calculate the difference 32 between the estimator-determined flow rate and the static value chosen with the 33 BPS/PPS options. If the flow rate is higher than the specified BPS/PPS, 0 will 34 be used instead of a negative value. In other words, "max(0, rateest#_rate - 35 rateest#_bps)" is used. 36 .TP 37 [\fB!\fP] \fB\-\-rateest\-lt\fP 38 Match if rate is less than given rate/estimator. 39 .TP 40 [\fB!\fP] \fB\-\-rateest\-gt\fP 41 Match if rate is greater than given rate/estimator. 42 .TP 43 [\fB!\fP] \fB\-\-rateest\-eq\fP 44 Match if rate is equal to given rate/estimator. 45 .PP 46 In the so-called "absolute mode", only one rate estimator is used and compared 47 against a static value, while in "relative mode", two rate estimators are 48 compared against another. 49 .TP 50 \fB\-\-rateest\fP \fIname\fP 51 Name of the one rate estimator for absolute mode. 52 .TP 53 \fB\-\-rateest1\fP \fIname\fP 54 .TP 55 \fB\-\-rateest2\fP \fIname\fP 56 The names of the two rate estimators for relative mode. 57 .TP 58 \fB\-\-rateest\-bps\fP [\fIvalue\fP] 59 .TP 60 \fB\-\-rateest\-pps\fP [\fIvalue\fP] 61 .TP 62 \fB\-\-rateest\-bps1\fP [\fIvalue\fP] 63 .TP 64 \fB\-\-rateest\-bps2\fP [\fIvalue\fP] 65 .TP 66 \fB\-\-rateest\-pps1\fP [\fIvalue\fP] 67 .TP 68 \fB\-\-rateest\-pps2\fP [\fIvalue\fP] 69 Compare the estimator(s) by bytes or packets per second, and compare against 70 the chosen value. See the above bullet list for which option is to be used in 71 which case. A unit suffix may be used - available ones are: bit, [kmgt]bit, 72 [KMGT]ibit, Bps, [KMGT]Bps, [KMGT]iBps. 73 .PP 74 Example: This is what can be used to route outgoing data connections from an 75 FTP server over two lines based on the available bandwidth at the time the data 76 connection was started: 77 .PP 78 # Estimate outgoing rates 79 .PP 80 iptables \-t mangle \-A POSTROUTING \-o eth0 \-j RATEEST \-\-rateest\-name eth0 81 \-\-rateest\-interval 250ms \-\-rateest\-ewma 0.5s 82 .PP 83 iptables \-t mangle \-A POSTROUTING \-o ppp0 \-j RATEEST \-\-rateest\-name ppp0 84 \-\-rateest\-interval 250ms \-\-rateest\-ewma 0.5s 85 .PP 86 # Mark based on available bandwidth 87 .PP 88 iptables \-t mangle \-A balance \-m conntrack \-\-ctstate NEW \-m helper \-\-helper ftp 89 \-m rateest \-\-rateest\-delta \-\-rateest1 eth0 \-\-rateest\-bps1 2.5mbit \-\-rateest\-gt 90 \-\-rateest2 ppp0 \-\-rateest\-bps2 2mbit \-j CONNMARK \-\-set\-mark 1 91 .PP 92 iptables \-t mangle \-A balance \-m conntrack \-\-ctstate NEW \-m helper \-\-helper ftp 93 \-m rateest \-\-rateest\-delta \-\-rateest1 ppp0 \-\-rateest\-bps1 2mbit \-\-rateest\-gt 94 \-\-rateest2 eth0 \-\-rateest\-bps2 2.5mbit \-j CONNMARK \-\-set\-mark 2 95 .PP 96 iptables \-t mangle \-A balance \-j CONNMARK \-\-restore\-mark 97
