1 /*------------------------------------------------------------------------ 2 * smc9000.h 3 * 4 * Copyright (C) 1998 by Daniel Engstrm 5 * Copyright (C) 1996 by Erik Stahlman 6 * 7 * This software may be used and distributed according to the terms 8 * of the GNU Public License, incorporated herein by reference. 9 * 10 * This file contains register information and access macros for 11 * the SMC91xxx chipset. 12 * 13 * Information contained in this file was obtained from the SMC91C94 14 * manual from SMC. To get a copy, if you really want one, you can find 15 * information under www.smsc.com in the components division. 16 * ( this thanks to advice from Donald Becker ). 17 * 18 * Authors 19 * Daniel Engstrm <daniel.engstrom (at) riksnett.no> 20 * Erik Stahlman <erik (at) vt.edu> 21 * 22 * History 23 * 96-01-06 Erik Stahlman moved definitions here from main .c 24 * file 25 * 96-01-19 Erik Stahlman polished this up some, and added 26 * better error handling 27 * 98-09-25 Daniel Engstrm adjusted for Etherboot 28 * 98-09-27 Daniel Engstrm moved some static strings back to the 29 * main .c file 30 * --------------------------------------------------------------------------*/ 31 32 FILE_LICENCE ( GPL_ANY ); 33 34 #ifndef _SMC9000_H_ 35 # define _SMC9000_H_ 36 37 /* I want some simple types */ 38 typedef unsigned char byte; 39 typedef unsigned short word; 40 typedef unsigned long int dword; 41 42 /*--------------------------------------------------------------- 43 * 44 * A description of the SMC registers is probably in order here, 45 * although for details, the SMC datasheet is invaluable. 46 * 47 * Basically, the chip has 4 banks of registers ( 0 to 3 ), which 48 * are accessed by writing a number into the BANK_SELECT register 49 * ( I also use a SMC_SELECT_BANK macro for this ). 50 * 51 * The banks are configured so that for most purposes, bank 2 is all 52 * that is needed for simple run time tasks. 53 * ----------------------------------------------------------------------*/ 54 55 /* 56 * Bank Select Register: 57 * 58 * yyyy yyyy 0000 00xx 59 * xx = bank number 60 * yyyy yyyy = 0x33, for identification purposes. 61 */ 62 #define BANK_SELECT 14 63 64 /* BANK 0 */ 65 66 #define TCR 0 /* transmit control register */ 67 #define TCR_ENABLE 0x0001 /* if this is 1, we can transmit */ 68 #define TCR_FDUPLX 0x0800 /* receive packets sent out */ 69 #define TCR_STP_SQET 0x1000 /* stop transmitting if Signal quality error */ 70 #define TCR_MON_CNS 0x0400 /* monitors the carrier status */ 71 #define TCR_PAD_ENABLE 0x0080 /* pads short packets to 64 bytes */ 72 73 #define TCR_CLEAR 0 /* do NOTHING */ 74 /* the normal settings for the TCR register : */ 75 #define TCR_NORMAL (TCR_ENABLE | TCR_PAD_ENABLE) 76 77 78 #define EPH_STATUS 2 79 #define ES_LINK_OK 0x4000 /* is the link integrity ok ? */ 80 81 #define RCR 4 82 #define RCR_SOFTRESET 0x8000 /* resets the chip */ 83 #define RCR_STRIP_CRC 0x200 /* strips CRC */ 84 #define RCR_ENABLE 0x100 /* IFF this is set, we can receive packets */ 85 #define RCR_ALMUL 0x4 /* receive all multicast packets */ 86 #define RCR_PROMISC 0x2 /* enable promiscuous mode */ 87 88 /* the normal settings for the RCR register : */ 89 #define RCR_NORMAL (RCR_STRIP_CRC | RCR_ENABLE) 90 #define RCR_CLEAR 0x0 /* set it to a base state */ 91 92 #define COUNTER 6 93 #define MIR 8 94 #define MCR 10 95 /* 12 is reserved */ 96 97 // Receive/Phy Control Register 98 /* BANK 0 */ 99 #define RPC_REG 0x000A 100 #define RPC_SPEED 0x2000 // When 1 PHY is in 100Mbps mode. 101 #define RPC_DPLX 0x1000 // When 1 PHY is in Full-Duplex Mode 102 #define RPC_ANEG 0x0800 // When 1 PHY is in Auto-Negotiate Mode 103 #define RPC_LSXA_SHFT 5 // Bits to shift LS2A,LS1A,LS0A to lsb 104 #define RPC_LSXB_SHFT 2 // Bits to get LS2B,LS1B,LS0B to lsb 105 #define RPC_LED_100_10 (0x00) // LED = 100Mbps OR's with 10Mbps link detect 106 #define RPC_LED_RES (0x01) // LED = Reserved 107 #define RPC_LED_10 (0x02) // LED = 10Mbps link detect 108 #define RPC_LED_FD (0x03) // LED = Full Duplex Mode 109 #define RPC_LED_TX_RX (0x04) // LED = TX or RX packet occurred 110 #define RPC_LED_100 (0x05) // LED = 100Mbps link dectect 111 #define RPC_LED_TX (0x06) // LED = TX packet occurred 112 #define RPC_LED_RX (0x07) // LED = RX packet occurred 113 #define RPC_DEFAULT (RPC_ANEG | (RPC_LED_100 << RPC_LSXA_SHFT) | (RPC_LED_FD << RPC_LSXB_SHFT) | RPC_SPEED | RPC_DPLX) 114 115 // Receive/Phy Control Register 116 /* BANK 0 */ 117 #define RPC_REG 0x000A 118 #define RPC_SPEED 0x2000 // When 1 PHY is in 100Mbps mode. 119 #define RPC_DPLX 0x1000 // When 1 PHY is in Full-Duplex Mode 120 #define RPC_ANEG 0x0800 // When 1 PHY is in Auto-Negotiate Mode 121 #define RPC_LSXA_SHFT 5 // Bits to shift LS2A,LS1A,LS0A to lsb 122 #define RPC_LSXB_SHFT 2 // Bits to get LS2B,LS1B,LS0B to lsb 123 #define RPC_LED_100_10 (0x00) // LED = 100Mbps OR's with 10Mbps link detect 124 #define RPC_LED_RES (0x01) // LED = Reserved 125 #define RPC_LED_10 (0x02) // LED = 10Mbps link detect 126 #define RPC_LED_FD (0x03) // LED = Full Duplex Mode 127 #define RPC_LED_TX_RX (0x04) // LED = TX or RX packet occurred 128 #define RPC_LED_100 (0x05) // LED = 100Mbps link dectect 129 #define RPC_LED_TX (0x06) // LED = TX packet occurred 130 #define RPC_LED_RX (0x07) // LED = RX packet occurred 131 #define RPC_DEFAULT (RPC_ANEG | (RPC_LED_100 << RPC_LSXA_SHFT) | (RPC_LED_FD << RPC_LSXB_SHFT) | RPC_SPEED | RPC_DPLX) 132 133 /* BANK 1 */ 134 #define CONFIG 0 135 #define CFG_AUI_SELECT 0x100 136 #define BASE 2 137 #define ADDR0 4 138 #define ADDR1 6 139 #define ADDR2 8 140 #define GENERAL 10 141 #define CONTROL 12 142 #define CTL_POWERDOWN 0x2000 143 #define CTL_LE_ENABLE 0x80 144 #define CTL_CR_ENABLE 0x40 145 #define CTL_TE_ENABLE 0x0020 146 #define CTL_AUTO_RELEASE 0x0800 147 #define CTL_EPROM_ACCESS 0x0003 /* high if Eprom is being read */ 148 149 /* BANK 2 */ 150 #define MMU_CMD 0 151 #define MC_BUSY 1 /* only readable bit in the register */ 152 #define MC_NOP 0 153 #define MC_ALLOC 0x20 /* or with number of 256 byte packets */ 154 #define MC_RESET 0x40 155 #define MC_REMOVE 0x60 /* remove the current rx packet */ 156 #define MC_RELEASE 0x80 /* remove and release the current rx packet */ 157 #define MC_FREEPKT 0xA0 /* Release packet in PNR register */ 158 #define MC_ENQUEUE 0xC0 /* Enqueue the packet for transmit */ 159 160 #define PNR_ARR 2 161 #define FIFO_PORTS 4 162 163 #define FP_RXEMPTY 0x8000 164 #define FP_TXEMPTY 0x80 165 166 #define POINTER 6 167 #define PTR_READ 0x2000 168 #define PTR_RCV 0x8000 169 #define PTR_AUTOINC 0x4000 170 #define PTR_AUTO_INC 0x0040 171 172 #define DATA_1 8 173 #define DATA_2 10 174 #define INTERRUPT 12 175 176 #define INT_MASK 13 177 #define IM_RCV_INT 0x1 178 #define IM_TX_INT 0x2 179 #define IM_TX_EMPTY_INT 0x4 180 #define IM_ALLOC_INT 0x8 181 #define IM_RX_OVRN_INT 0x10 182 #define IM_EPH_INT 0x20 183 #define IM_ERCV_INT 0x40 /* not on SMC9192 */ 184 185 /* BANK 3 */ 186 #define MULTICAST1 0 187 #define MULTICAST2 2 188 #define MULTICAST3 4 189 #define MULTICAST4 6 190 #define MGMT 8 191 #define REVISION 10 /* ( hi: chip id low: rev # ) */ 192 193 // Management Interface Register (MII) 194 #define MII_REG 0x0008 195 #define MII_MSK_CRS100 0x4000 // Disables CRS100 detection during tx half dup 196 #define MII_MDOE 0x0008 // MII Output Enable 197 #define MII_MCLK 0x0004 // MII Clock, pin MDCLK 198 #define MII_MDI 0x0002 // MII Input, pin MDI 199 #define MII_MDO 0x0001 // MII Output, pin MDO 200 201 /* this is NOT on SMC9192 */ 202 #define ERCV 12 203 204 /* Note that 9194 and 9196 have the smame chip id, 205 * the 9196 will have revisions starting at 6 */ 206 #define CHIP_9190 3 207 #define CHIP_9194 4 208 #define CHIP_9195 5 209 #define CHIP_9196 4 210 #define CHIP_91100 7 211 #define CHIP_91100FD 8 212 213 #define REV_9196 6 214 215 /* 216 * Transmit status bits 217 */ 218 #define TS_SUCCESS 0x0001 219 #define TS_LOSTCAR 0x0400 220 #define TS_LATCOL 0x0200 221 #define TS_16COL 0x0010 222 223 /* 224 * Receive status bits 225 */ 226 #define RS_ALGNERR 0x8000 227 #define RS_BADCRC 0x2000 228 #define RS_ODDFRAME 0x1000 229 #define RS_TOOLONG 0x0800 230 #define RS_TOOSHORT 0x0400 231 #define RS_MULTICAST 0x0001 232 #define RS_ERRORS (RS_ALGNERR | RS_BADCRC | RS_TOOLONG | RS_TOOSHORT) 233 234 // PHY Register Addresses (LAN91C111 Internal PHY) 235 236 // PHY Control Register 237 #define PHY_CNTL_REG 0x00 238 #define PHY_CNTL_RST 0x8000 // 1=PHY Reset 239 #define PHY_CNTL_LPBK 0x4000 // 1=PHY Loopback 240 #define PHY_CNTL_SPEED 0x2000 // 1=100Mbps, 0=10Mpbs 241 #define PHY_CNTL_ANEG_EN 0x1000 // 1=Enable Auto negotiation 242 #define PHY_CNTL_PDN 0x0800 // 1=PHY Power Down mode 243 #define PHY_CNTL_MII_DIS 0x0400 // 1=MII 4 bit interface disabled 244 #define PHY_CNTL_ANEG_RST 0x0200 // 1=Reset Auto negotiate 245 #define PHY_CNTL_DPLX 0x0100 // 1=Full Duplex, 0=Half Duplex 246 #define PHY_CNTL_COLTST 0x0080 // 1= MII Colision Test 247 248 // PHY Status Register 249 #define PHY_STAT_REG 0x01 250 #define PHY_STAT_CAP_T4 0x8000 // 1=100Base-T4 capable 251 #define PHY_STAT_CAP_TXF 0x4000 // 1=100Base-X full duplex capable 252 #define PHY_STAT_CAP_TXH 0x2000 // 1=100Base-X half duplex capable 253 #define PHY_STAT_CAP_TF 0x1000 // 1=10Mbps full duplex capable 254 #define PHY_STAT_CAP_TH 0x0800 // 1=10Mbps half duplex capable 255 #define PHY_STAT_CAP_SUPR 0x0040 // 1=recv mgmt frames with not preamble 256 #define PHY_STAT_ANEG_ACK 0x0020 // 1=ANEG has completed 257 #define PHY_STAT_REM_FLT 0x0010 // 1=Remote Fault detected 258 #define PHY_STAT_CAP_ANEG 0x0008 // 1=Auto negotiate capable 259 #define PHY_STAT_LINK 0x0004 // 1=valid link 260 #define PHY_STAT_JAB 0x0002 // 1=10Mbps jabber condition 261 #define PHY_STAT_EXREG 0x0001 // 1=extended registers implemented 262 263 // PHY Identifier Registers 264 #define PHY_ID1_REG 0x02 // PHY Identifier 1 265 #define PHY_ID2_REG 0x03 // PHY Identifier 2 266 267 // PHY Auto-Negotiation Advertisement Register 268 #define PHY_AD_REG 0x04 269 #define PHY_AD_NP 0x8000 // 1=PHY requests exchange of Next Page 270 #define PHY_AD_ACK 0x4000 // 1=got link code word from remote 271 #define PHY_AD_RF 0x2000 // 1=advertise remote fault 272 #define PHY_AD_T4 0x0200 // 1=PHY is capable of 100Base-T4 273 #define PHY_AD_TX_FDX 0x0100 // 1=PHY is capable of 100Base-TX FDPLX 274 #define PHY_AD_TX_HDX 0x0080 // 1=PHY is capable of 100Base-TX HDPLX 275 #define PHY_AD_10_FDX 0x0040 // 1=PHY is capable of 10Base-T FDPLX 276 #define PHY_AD_10_HDX 0x0020 // 1=PHY is capable of 10Base-T HDPLX 277 #define PHY_AD_CSMA 0x0001 // 1=PHY is capable of 802.3 CMSA 278 279 // PHY Auto-negotiation Remote End Capability Register 280 #define PHY_RMT_REG 0x05 281 // Uses same bit definitions as PHY_AD_REG 282 283 // PHY Configuration Register 1 284 #define PHY_CFG1_REG 0x10 285 #define PHY_CFG1_LNKDIS 0x8000 // 1=Rx Link Detect Function disabled 286 #define PHY_CFG1_XMTDIS 0x4000 // 1=TP Transmitter Disabled 287 #define PHY_CFG1_XMTPDN 0x2000 // 1=TP Transmitter Powered Down 288 #define PHY_CFG1_BYPSCR 0x0400 // 1=Bypass scrambler/descrambler 289 #define PHY_CFG1_UNSCDS 0x0200 // 1=Unscramble Idle Reception Disable 290 #define PHY_CFG1_EQLZR 0x0100 // 1=Rx Equalizer Disabled 291 #define PHY_CFG1_CABLE 0x0080 // 1=STP(150ohm), 0=UTP(100ohm) 292 #define PHY_CFG1_RLVL0 0x0040 // 1=Rx Squelch level reduced by 4.5db 293 #define PHY_CFG1_TLVL_SHIFT 2 // Transmit Output Level Adjust 294 #define PHY_CFG1_TLVL_MASK 0x003C 295 #define PHY_CFG1_TRF_MASK 0x0003 // Transmitter Rise/Fall time 296 297 298 // PHY Configuration Register 2 299 #define PHY_CFG2_REG 0x11 300 #define PHY_CFG2_APOLDIS 0x0020 // 1=Auto Polarity Correction disabled 301 #define PHY_CFG2_JABDIS 0x0010 // 1=Jabber disabled 302 #define PHY_CFG2_MREG 0x0008 // 1=Multiple register access (MII mgt) 303 #define PHY_CFG2_INTMDIO 0x0004 // 1=Interrupt signaled with MDIO pulseo 304 305 // PHY Status Output (and Interrupt status) Register 306 #define PHY_INT_REG 0x12 // Status Output (Interrupt Status) 307 #define PHY_INT_INT 0x8000 // 1=bits have changed since last read 308 #define PHY_INT_LNKFAIL 0x4000 // 1=Link Not detected 309 #define PHY_INT_LOSSSYNC 0x2000 // 1=Descrambler has lost sync 310 #define PHY_INT_CWRD 0x1000 // 1=Invalid 4B5B code detected on rx 311 #define PHY_INT_SSD 0x0800 // 1=No Start Of Stream detected on rx 312 #define PHY_INT_ESD 0x0400 // 1=No End Of Stream detected on rx 313 #define PHY_INT_RPOL 0x0200 // 1=Reverse Polarity detected 314 #define PHY_INT_JAB 0x0100 // 1=Jabber detected 315 #define PHY_INT_SPDDET 0x0080 // 1=100Base-TX mode, 0=10Base-T mode 316 #define PHY_INT_DPLXDET 0x0040 // 1=Device in Full Duplex 317 318 // PHY Interrupt/Status Mask Register 319 #define PHY_MASK_REG 0x13 // Interrupt Mask 320 // Uses the same bit definitions as PHY_INT_REG 321 322 323 // PHY Register Addresses (LAN91C111 Internal PHY) 324 325 // PHY Control Register 326 #define PHY_CNTL_REG 0x00 327 #define PHY_CNTL_RST 0x8000 // 1=PHY Reset 328 #define PHY_CNTL_LPBK 0x4000 // 1=PHY Loopback 329 #define PHY_CNTL_SPEED 0x2000 // 1=100Mbps, 0=10Mpbs 330 #define PHY_CNTL_ANEG_EN 0x1000 // 1=Enable Auto negotiation 331 #define PHY_CNTL_PDN 0x0800 // 1=PHY Power Down mode 332 #define PHY_CNTL_MII_DIS 0x0400 // 1=MII 4 bit interface disabled 333 #define PHY_CNTL_ANEG_RST 0x0200 // 1=Reset Auto negotiate 334 #define PHY_CNTL_DPLX 0x0100 // 1=Full Duplex, 0=Half Duplex 335 #define PHY_CNTL_COLTST 0x0080 // 1= MII Colision Test 336 337 // PHY Status Register 338 #define PHY_STAT_REG 0x01 339 #define PHY_STAT_CAP_T4 0x8000 // 1=100Base-T4 capable 340 #define PHY_STAT_CAP_TXF 0x4000 // 1=100Base-X full duplex capable 341 #define PHY_STAT_CAP_TXH 0x2000 // 1=100Base-X half duplex capable 342 #define PHY_STAT_CAP_TF 0x1000 // 1=10Mbps full duplex capable 343 #define PHY_STAT_CAP_TH 0x0800 // 1=10Mbps half duplex capable 344 #define PHY_STAT_CAP_SUPR 0x0040 // 1=recv mgmt frames with not preamble 345 #define PHY_STAT_ANEG_ACK 0x0020 // 1=ANEG has completed 346 #define PHY_STAT_REM_FLT 0x0010 // 1=Remote Fault detected 347 #define PHY_STAT_CAP_ANEG 0x0008 // 1=Auto negotiate capable 348 #define PHY_STAT_LINK 0x0004 // 1=valid link 349 #define PHY_STAT_JAB 0x0002 // 1=10Mbps jabber condition 350 #define PHY_STAT_EXREG 0x0001 // 1=extended registers implemented 351 352 // PHY Identifier Registers 353 #define PHY_ID1_REG 0x02 // PHY Identifier 1 354 #define PHY_ID2_REG 0x03 // PHY Identifier 2 355 356 // PHY Auto-Negotiation Advertisement Register 357 #define PHY_AD_REG 0x04 358 #define PHY_AD_NP 0x8000 // 1=PHY requests exchange of Next Page 359 #define PHY_AD_ACK 0x4000 // 1=got link code word from remote 360 #define PHY_AD_RF 0x2000 // 1=advertise remote fault 361 #define PHY_AD_T4 0x0200 // 1=PHY is capable of 100Base-T4 362 #define PHY_AD_TX_FDX 0x0100 // 1=PHY is capable of 100Base-TX FDPLX 363 #define PHY_AD_TX_HDX 0x0080 // 1=PHY is capable of 100Base-TX HDPLX 364 #define PHY_AD_10_FDX 0x0040 // 1=PHY is capable of 10Base-T FDPLX 365 #define PHY_AD_10_HDX 0x0020 // 1=PHY is capable of 10Base-T HDPLX 366 #define PHY_AD_CSMA 0x0001 // 1=PHY is capable of 802.3 CMSA 367 368 // PHY Auto-negotiation Remote End Capability Register 369 #define PHY_RMT_REG 0x05 370 // Uses same bit definitions as PHY_AD_REG 371 372 // PHY Configuration Register 1 373 #define PHY_CFG1_REG 0x10 374 #define PHY_CFG1_LNKDIS 0x8000 // 1=Rx Link Detect Function disabled 375 #define PHY_CFG1_XMTDIS 0x4000 // 1=TP Transmitter Disabled 376 #define PHY_CFG1_XMTPDN 0x2000 // 1=TP Transmitter Powered Down 377 #define PHY_CFG1_BYPSCR 0x0400 // 1=Bypass scrambler/descrambler 378 #define PHY_CFG1_UNSCDS 0x0200 // 1=Unscramble Idle Reception Disable 379 #define PHY_CFG1_EQLZR 0x0100 // 1=Rx Equalizer Disabled 380 #define PHY_CFG1_CABLE 0x0080 // 1=STP(150ohm), 0=UTP(100ohm) 381 #define PHY_CFG1_RLVL0 0x0040 // 1=Rx Squelch level reduced by 4.5db 382 #define PHY_CFG1_TLVL_SHIFT 2 // Transmit Output Level Adjust 383 #define PHY_CFG1_TLVL_MASK 0x003C 384 #define PHY_CFG1_TRF_MASK 0x0003 // Transmitter Rise/Fall time 385 386 387 // PHY Configuration Register 2 388 #define PHY_CFG2_REG 0x11 389 #define PHY_CFG2_APOLDIS 0x0020 // 1=Auto Polarity Correction disabled 390 #define PHY_CFG2_JABDIS 0x0010 // 1=Jabber disabled 391 #define PHY_CFG2_MREG 0x0008 // 1=Multiple register access (MII mgt) 392 #define PHY_CFG2_INTMDIO 0x0004 // 1=Interrupt signaled with MDIO pulseo 393 394 // PHY Status Output (and Interrupt status) Register 395 #define PHY_INT_REG 0x12 // Status Output (Interrupt Status) 396 #define PHY_INT_INT 0x8000 // 1=bits have changed since last read 397 #define PHY_INT_LNKFAIL 0x4000 // 1=Link Not detected 398 #define PHY_INT_LOSSSYNC 0x2000 // 1=Descrambler has lost sync 399 #define PHY_INT_CWRD 0x1000 // 1=Invalid 4B5B code detected on rx 400 #define PHY_INT_SSD 0x0800 // 1=No Start Of Stream detected on rx 401 #define PHY_INT_ESD 0x0400 // 1=No End Of Stream detected on rx 402 #define PHY_INT_RPOL 0x0200 // 1=Reverse Polarity detected 403 #define PHY_INT_JAB 0x0100 // 1=Jabber detected 404 #define PHY_INT_SPDDET 0x0080 // 1=100Base-TX mode, 0=10Base-T mode 405 #define PHY_INT_DPLXDET 0x0040 // 1=Device in Full Duplex 406 407 // PHY Interrupt/Status Mask Register 408 #define PHY_MASK_REG 0x13 // Interrupt Mask 409 // Uses the same bit definitions as PHY_INT_REG 410 411 412 /*------------------------------------------------------------------------- 413 * I define some macros to make it easier to do somewhat common 414 * or slightly complicated, repeated tasks. 415 --------------------------------------------------------------------------*/ 416 417 /* select a register bank, 0 to 3 */ 418 419 #define SMC_SELECT_BANK(x, y) { _outw( y, x + BANK_SELECT ); } 420 421 /* define a small delay for the reset */ 422 #define SMC_DELAY(x) { inw( x + RCR );\ 423 inw( x + RCR );\ 424 inw( x + RCR ); } 425 426 427 #endif /* _SMC_9000_H_ */ 428 429
