1 /* 2 * Copyright (c) 1993 Herb Peyerl (hpeyerl (at) novatel.ca) All rights reserved. 3 * 4 * Redistribution and use in source and binary forms, with or without 5 * modification, are permitted provided that the following conditions are 6 * met: 1. Redistributions of source code must retain the above copyright 7 * notice, this list of conditions and the following disclaimer. 2. The name 8 * of the author may not be used to endorse or promote products derived from 9 * this software without specific prior written permission 10 * 11 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR IMPLIED 12 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF 13 * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO 14 * EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, 15 * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED 16 * TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR 17 * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF 18 * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING 19 * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS 20 * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 21 * 22 October 2, 1994 23 24 Modified by: Andres Vega Garcia 25 26 INRIA - Sophia Antipolis, France 27 e-mail: avega (at) sophia.inria.fr 28 finger: avega (at) pax.inria.fr 29 30 */ 31 32 FILE_LICENCE ( BSD3 ); 33 34 /* 35 * Created from if_epreg.h by Fred Gray (fgray (at) rice.edu) to support the 36 * 3c590 family. 37 */ 38 39 /* 40 * Modified by Shusuke Nisiyama <shu (at) athena.qe.eng.hokudai.ac.jp> 41 * for etherboot 42 * Mar. 14, 2000 43 */ 44 45 /* 46 * Ethernet software status per interface. 47 */ 48 49 /* 50 * Some global constants 51 */ 52 53 #define TX_INIT_RATE 16 54 #define TX_INIT_MAX_RATE 64 55 #define RX_INIT_LATENCY 64 56 #define RX_INIT_EARLY_THRESH 64 57 #define MIN_RX_EARLY_THRESHF 16 /* not less than ether_header */ 58 #define MIN_RX_EARLY_THRESHL 4 59 60 #define EEPROMSIZE 0x40 61 #define MAX_EEPROMBUSY 1000 62 #define VX_LAST_TAG 0xd7 63 #define VX_MAX_BOARDS 16 64 #define VX_ID_PORT 0x100 65 66 /* 67 * some macros to acces long named fields 68 */ 69 #define BASE (eth_nic_base) 70 71 /* 72 * Commands to read/write EEPROM trough EEPROM command register (Window 0, 73 * Offset 0xa) 74 */ 75 #define EEPROM_CMD_RD 0x0080 /* Read: Address required (5 bits) */ 76 #define EEPROM_CMD_WR 0x0040 /* Write: Address required (5 bits) */ 77 #define EEPROM_CMD_ERASE 0x00c0 /* Erase: Address required (5 bits) */ 78 #define EEPROM_CMD_EWEN 0x0030 /* Erase/Write Enable: No data required */ 79 80 #define EEPROM_BUSY (1<<15) 81 82 /* 83 * Some short functions, worth to let them be a macro 84 */ 85 86 /************************************************************************** 87 * * 88 * These define the EEPROM data structure. They are used in the probe 89 * function to verify the existence of the adapter after having sent 90 * the ID_Sequence. 91 * 92 * There are others but only the ones we use are defined here. 93 * 94 **************************************************************************/ 95 96 #define EEPROM_NODE_ADDR_0 0x0 /* Word */ 97 #define EEPROM_NODE_ADDR_1 0x1 /* Word */ 98 #define EEPROM_NODE_ADDR_2 0x2 /* Word */ 99 #define EEPROM_PROD_ID 0x3 /* 0x9[0-f]50 */ 100 #define EEPROM_MFG_ID 0x7 /* 0x6d50 */ 101 #define EEPROM_ADDR_CFG 0x8 /* Base addr */ 102 #define EEPROM_RESOURCE_CFG 0x9 /* IRQ. Bits 12-15 */ 103 #define EEPROM_OEM_ADDR_0 0xa /* Word */ 104 #define EEPROM_OEM_ADDR_1 0xb /* Word */ 105 #define EEPROM_OEM_ADDR_2 0xc /* Word */ 106 #define EEPROM_SOFT_INFO_2 0xf /* Software information 2 */ 107 108 #define NO_RX_OVN_ANOMALY (1<<5) 109 110 /************************************************************************** 111 * * 112 * These are the registers for the 3Com 3c509 and their bit patterns when * 113 * applicable. They have been taken out the the "EtherLink III Parallel * 114 * Tasking EISA and ISA Technical Reference" "Beta Draft 10/30/92" manual * 115 * from 3com. * 116 * * 117 **************************************************************************/ 118 119 #define VX_COMMAND 0x0e /* Write. BASE+0x0e is always a 120 * command reg. */ 121 #define VX_STATUS 0x0e /* Read. BASE+0x0e is always status 122 * reg. */ 123 #define VX_WINDOW 0x0f /* Read. BASE+0x0f is always window 124 * reg. */ 125 /* 126 * Window 0 registers. Setup. 127 */ 128 /* Write */ 129 #define VX_W0_EEPROM_DATA 0x0c 130 #define VX_W0_EEPROM_COMMAND 0x0a 131 #define VX_W0_RESOURCE_CFG 0x08 132 #define VX_W0_ADDRESS_CFG 0x06 133 #define VX_W0_CONFIG_CTRL 0x04 134 /* Read */ 135 #define VX_W0_PRODUCT_ID 0x02 136 #define VX_W0_MFG_ID 0x00 137 138 139 /* 140 * Window 1 registers. Operating Set. 141 */ 142 /* Write */ 143 #define VX_W1_TX_PIO_WR_2 0x02 144 #define VX_W1_TX_PIO_WR_1 0x00 145 /* Read */ 146 #define VX_W1_FREE_TX 0x0c 147 #define VX_W1_TX_STATUS 0x0b /* byte */ 148 #define VX_W1_TIMER 0x0a /* byte */ 149 #define VX_W1_RX_STATUS 0x08 150 #define VX_W1_RX_PIO_RD_2 0x02 151 #define VX_W1_RX_PIO_RD_1 0x00 152 153 /* 154 * Window 2 registers. Station Address Setup/Read 155 */ 156 /* Read/Write */ 157 #define VX_W2_ADDR_5 0x05 158 #define VX_W2_ADDR_4 0x04 159 #define VX_W2_ADDR_3 0x03 160 #define VX_W2_ADDR_2 0x02 161 #define VX_W2_ADDR_1 0x01 162 #define VX_W2_ADDR_0 0x00 163 164 /* 165 * Window 3 registers. FIFO Management. 166 */ 167 /* Read */ 168 #define VX_W3_INTERNAL_CFG 0x00 169 #define VX_W3_RESET_OPT 0x08 170 #define VX_W3_FREE_TX 0x0c 171 #define VX_W3_FREE_RX 0x0a 172 173 /* 174 * Window 4 registers. Diagnostics. 175 */ 176 /* Read/Write */ 177 #define VX_W4_MEDIA_TYPE 0x0a 178 #define VX_W4_CTRLR_STATUS 0x08 179 #define VX_W4_NET_DIAG 0x06 180 #define VX_W4_FIFO_DIAG 0x04 181 #define VX_W4_HOST_DIAG 0x02 182 #define VX_W4_TX_DIAG 0x00 183 184 /* 185 * Window 5 Registers. Results and Internal status. 186 */ 187 /* Read */ 188 #define VX_W5_READ_0_MASK 0x0c 189 #define VX_W5_INTR_MASK 0x0a 190 #define VX_W5_RX_FILTER 0x08 191 #define VX_W5_RX_EARLY_THRESH 0x06 192 #define VX_W5_TX_AVAIL_THRESH 0x02 193 #define VX_W5_TX_START_THRESH 0x00 194 195 /* 196 * Window 6 registers. Statistics. 197 */ 198 /* Read/Write */ 199 #define TX_TOTAL_OK 0x0c 200 #define RX_TOTAL_OK 0x0a 201 #define TX_DEFERRALS 0x08 202 #define RX_FRAMES_OK 0x07 203 #define TX_FRAMES_OK 0x06 204 #define RX_OVERRUNS 0x05 205 #define TX_COLLISIONS 0x04 206 #define TX_AFTER_1_COLLISION 0x03 207 #define TX_AFTER_X_COLLISIONS 0x02 208 #define TX_NO_SQE 0x01 209 #define TX_CD_LOST 0x00 210 211 /**************************************** 212 * 213 * Register definitions. 214 * 215 ****************************************/ 216 217 /* 218 * Command register. All windows. 219 * 220 * 16 bit register. 221 * 15-11: 5-bit code for command to be executed. 222 * 10-0: 11-bit arg if any. For commands with no args; 223 * this can be set to anything. 224 */ 225 #define GLOBAL_RESET (unsigned short) 0x0000 /* Wait at least 1ms 226 * after issuing */ 227 #define WINDOW_SELECT (unsigned short) (0x1<<11) 228 #define START_TRANSCEIVER (unsigned short) (0x2<<11) /* Read ADDR_CFG reg to 229 * determine whether 230 * this is needed. If 231 * so; wait 800 uSec 232 * before using trans- 233 * ceiver. */ 234 #define RX_DISABLE (unsigned short) (0x3<<11) /* state disabled on 235 * power-up */ 236 #define RX_ENABLE (unsigned short) (0x4<<11) 237 #define RX_RESET (unsigned short) (0x5<<11) 238 #define RX_DISCARD_TOP_PACK (unsigned short) (0x8<<11) 239 #define TX_ENABLE (unsigned short) (0x9<<11) 240 #define TX_DISABLE (unsigned short) (0xa<<11) 241 #define TX_RESET (unsigned short) (0xb<<11) 242 #define REQ_INTR (unsigned short) (0xc<<11) 243 /* 244 * The following C_* acknowledge the various interrupts. Some of them don't 245 * do anything. See the manual. 246 */ 247 #define ACK_INTR (unsigned short) (0x6800) 248 # define C_INTR_LATCH (unsigned short) (ACK_INTR|0x1) 249 # define C_CARD_FAILURE (unsigned short) (ACK_INTR|0x2) 250 # define C_TX_COMPLETE (unsigned short) (ACK_INTR|0x4) 251 # define C_TX_AVAIL (unsigned short) (ACK_INTR|0x8) 252 # define C_RX_COMPLETE (unsigned short) (ACK_INTR|0x10) 253 # define C_RX_EARLY (unsigned short) (ACK_INTR|0x20) 254 # define C_INT_RQD (unsigned short) (ACK_INTR|0x40) 255 # define C_UPD_STATS (unsigned short) (ACK_INTR|0x80) 256 #define SET_INTR_MASK (unsigned short) (0xe<<11) 257 #define SET_RD_0_MASK (unsigned short) (0xf<<11) 258 #define SET_RX_FILTER (unsigned short) (0x10<<11) 259 # define FIL_INDIVIDUAL (unsigned short) (0x1) 260 # define FIL_MULTICAST (unsigned short) (0x02) 261 # define FIL_BRDCST (unsigned short) (0x04) 262 # define FIL_PROMISC (unsigned short) (0x08) 263 #define SET_RX_EARLY_THRESH (unsigned short) (0x11<<11) 264 #define SET_TX_AVAIL_THRESH (unsigned short) (0x12<<11) 265 #define SET_TX_START_THRESH (unsigned short) (0x13<<11) 266 #define STATS_ENABLE (unsigned short) (0x15<<11) 267 #define STATS_DISABLE (unsigned short) (0x16<<11) 268 #define STOP_TRANSCEIVER (unsigned short) (0x17<<11) 269 270 /* 271 * Status register. All windows. 272 * 273 * 15-13: Window number(0-7). 274 * 12: Command_in_progress. 275 * 11: reserved. 276 * 10: reserved. 277 * 9: reserved. 278 * 8: reserved. 279 * 7: Update Statistics. 280 * 6: Interrupt Requested. 281 * 5: RX Early. 282 * 4: RX Complete. 283 * 3: TX Available. 284 * 2: TX Complete. 285 * 1: Adapter Failure. 286 * 0: Interrupt Latch. 287 */ 288 #define S_INTR_LATCH (unsigned short) (0x1) 289 #define S_CARD_FAILURE (unsigned short) (0x2) 290 #define S_TX_COMPLETE (unsigned short) (0x4) 291 #define S_TX_AVAIL (unsigned short) (0x8) 292 #define S_RX_COMPLETE (unsigned short) (0x10) 293 #define S_RX_EARLY (unsigned short) (0x20) 294 #define S_INT_RQD (unsigned short) (0x40) 295 #define S_UPD_STATS (unsigned short) (0x80) 296 #define S_COMMAND_IN_PROGRESS (unsigned short) (0x1000) 297 298 #define VX_BUSY_WAIT while (inw(BASE + VX_STATUS) & S_COMMAND_IN_PROGRESS) 299 300 /* Address Config. Register. 301 * Window 0/Port 06 302 */ 303 304 #define ACF_CONNECTOR_BITS 14 305 #define ACF_CONNECTOR_UTP 0 306 #define ACF_CONNECTOR_AUI 1 307 #define ACF_CONNECTOR_BNC 3 308 309 #define INTERNAL_CONNECTOR_BITS 20 310 #define INTERNAL_CONNECTOR_MASK 0x01700000 311 312 /* 313 * FIFO Registers. RX Status. 314 * 315 * 15: Incomplete or FIFO empty. 316 * 14: 1: Error in RX Packet 0: Incomplete or no error. 317 * 13-11: Type of error. 318 * 1000 = Overrun. 319 * 1011 = Run Packet Error. 320 * 1100 = Alignment Error. 321 * 1101 = CRC Error. 322 * 1001 = Oversize Packet Error (>1514 bytes) 323 * 0010 = Dribble Bits. 324 * (all other error codes, no errors.) 325 * 326 * 10-0: RX Bytes (0-1514) 327 */ 328 #define ERR_INCOMPLETE (unsigned short) (0x8000) 329 #define ERR_RX (unsigned short) (0x4000) 330 #define ERR_MASK (unsigned short) (0x7800) 331 #define ERR_OVERRUN (unsigned short) (0x4000) 332 #define ERR_RUNT (unsigned short) (0x5800) 333 #define ERR_ALIGNMENT (unsigned short) (0x6000) 334 #define ERR_CRC (unsigned short) (0x6800) 335 #define ERR_OVERSIZE (unsigned short) (0x4800) 336 #define ERR_DRIBBLE (unsigned short) (0x1000) 337 338 /* 339 * TX Status. 340 * 341 * Reports the transmit status of a completed transmission. Writing this 342 * register pops the transmit completion stack. 343 * 344 * Window 1/Port 0x0b. 345 * 346 * 7: Complete 347 * 6: Interrupt on successful transmission requested. 348 * 5: Jabber Error (TP Only, TX Reset required. ) 349 * 4: Underrun (TX Reset required. ) 350 * 3: Maximum Collisions. 351 * 2: TX Status Overflow. 352 * 1-0: Undefined. 353 * 354 */ 355 #define TXS_COMPLETE 0x80 356 #define TXS_INTR_REQ 0x40 357 #define TXS_JABBER 0x20 358 #define TXS_UNDERRUN 0x10 359 #define TXS_MAX_COLLISION 0x8 360 #define TXS_STATUS_OVERFLOW 0x4 361 362 #define RS_AUI (1<<5) 363 #define RS_BNC (1<<4) 364 #define RS_UTP (1<<3) 365 #define RS_T4 (1<<0) 366 #define RS_TX (1<<1) 367 #define RS_FX (1<<2) 368 #define RS_MII (1<<6) 369 370 371 /* 372 * FIFO Status (Window 4) 373 * 374 * Supports FIFO diagnostics 375 * 376 * Window 4/Port 0x04.1 377 * 378 * 15: 1=RX receiving (RO). Set when a packet is being received 379 * into the RX FIFO. 380 * 14: Reserved 381 * 13: 1=RX underrun (RO). Generates Adapter Failure interrupt. 382 * Requires RX Reset or Global Reset command to recover. 383 * It is generated when you read past the end of a packet - 384 * reading past what has been received so far will give bad 385 * data. 386 * 12: 1=RX status overrun (RO). Set when there are already 8 387 * packets in the RX FIFO. While this bit is set, no additional 388 * packets are received. Requires no action on the part of 389 * the host. The condition is cleared once a packet has been 390 * read out of the RX FIFO. 391 * 11: 1=RX overrun (RO). Set when the RX FIFO is full (there 392 * may not be an overrun packet yet). While this bit is set, 393 * no additional packets will be received (some additional 394 * bytes can still be pending between the wire and the RX 395 * FIFO). Requires no action on the part of the host. The 396 * condition is cleared once a few bytes have been read out 397 * from the RX FIFO. 398 * 10: 1=TX overrun (RO). Generates adapter failure interrupt. 399 * Requires TX Reset or Global Reset command to recover. 400 * Disables Transmitter. 401 * 9-8: Unassigned. 402 * 7-0: Built in self test bits for the RX and TX FIFO's. 403 */ 404 #define FIFOS_RX_RECEIVING (unsigned short) 0x8000 405 #define FIFOS_RX_UNDERRUN (unsigned short) 0x2000 406 #define FIFOS_RX_STATUS_OVERRUN (unsigned short) 0x1000 407 #define FIFOS_RX_OVERRUN (unsigned short) 0x0800 408 #define FIFOS_TX_OVERRUN (unsigned short) 0x0400 409 410 /* 411 * Misc defines for various things. 412 */ 413 #define TAG_ADAPTER 0xd0 414 #define ACTIVATE_ADAPTER_TO_CONFIG 0xff 415 #define ENABLE_DRQ_IRQ 0x0001 416 #define MFG_ID 0x506d /* `TCM' */ 417 #define PROD_ID 0x5090 418 #define GO_WINDOW(x) outw(WINDOW_SELECT|(x),BASE+VX_COMMAND) 419 #define JABBER_GUARD_ENABLE 0x40 420 #define LINKBEAT_ENABLE 0x80 421 #define ENABLE_UTP (JABBER_GUARD_ENABLE | LINKBEAT_ENABLE) 422 #define DISABLE_UTP 0x0 423 #define RX_BYTES_MASK (unsigned short) (0x07ff) 424 #define RX_ERROR 0x4000 425 #define RX_INCOMPLETE 0x8000 426 #define TX_INDICATE 1<<15 427 #define is_eeprom_busy(b) (inw((b)+VX_W0_EEPROM_COMMAND)&EEPROM_BUSY) 428 429 #define VX_IOSIZE 0x20 430 431 #define VX_CONNECTORS 8 432 433 /* 434 * Local variables: 435 * c-basic-offset: 8 436 * End: 437 */ 438
