1 /* 2 * Device Tree file for Marvell Armada XP maxbcm board 3 * 4 * Copyright (C) 2013-2014 Marvell 5 * 6 * Lior Amsalem <alior (at) marvell.com> 7 * Gregory CLEMENT <gregory.clement (at) free-electrons.com> 8 * Thomas Petazzoni <thomas.petazzoni (at) free-electrons.com> 9 * 10 * This file is dual-licensed: you can use it either under the terms 11 * of the GPL or the X11 license, at your option. Note that this dual 12 * licensing only applies to this file, and not this project as a 13 * whole. 14 * 15 * a) This file is free software; you can redistribute it and/or 16 * modify it under the terms of the GNU General Public License as 17 * published by the Free Software Foundation; either version 2 of the 18 * License, or (at your option) any later version. 19 * 20 * This file is distributed in the hope that it will be useful 21 * but WITHOUT ANY WARRANTY; without even the implied warranty of 22 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 23 * GNU General Public License for more details. 24 * 25 * Or, alternatively 26 * 27 * b) Permission is hereby granted, free of charge, to any person 28 * obtaining a copy of this software and associated documentation 29 * files (the "Software"), to deal in the Software without 30 * restriction, including without limitation the rights to use 31 * copy, modify, merge, publish, distribute, sublicense, and/or 32 * sell copies of the Software, and to permit persons to whom the 33 * Software is furnished to do so, subject to the following 34 * conditions: 35 * 36 * The above copyright notice and this permission notice shall be 37 * included in all copies or substantial portions of the Software. 38 * 39 * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND 40 * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES 41 * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND 42 * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT 43 * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY 44 * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING 45 * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR 46 * OTHER DEALINGS IN THE SOFTWARE. 47 * 48 * Note: this Device Tree assumes that the bootloader has remapped the 49 * internal registers to 0xf1000000 (instead of the default 50 * 0xd0000000). The 0xf1000000 is the default used by the recent, 51 * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier 52 * boards were delivered with an older version of the bootloader that 53 * left internal registers mapped at 0xd0000000. If you are in this 54 * situation, you should either update your bootloader (preferred 55 * solution) or the below Device Tree should be adjusted. 56 */ 57 58 /dts-v1/; 59 #include <dt-bindings/gpio/gpio.h> 60 #include "armada-xp-mv78460.dtsi" 61 62 / { 63 model = "Marvell Armada XP MAXBCM"; 64 compatible = "marvell,axp-gp", "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp"; 65 66 chosen { 67 stdout-path = "serial0:115200n8"; 68 }; 69 70 aliases { 71 spi0 = &spi0; 72 }; 73 74 memory { 75 device_type = "memory"; 76 /* 77 * 8 GB of plug-in RAM modules by default.The amount 78 * of memory available can be changed by the 79 * bootloader according the size of the module 80 * actually plugged. However, memory between 81 * 0xF0000000 to 0xFFFFFFFF cannot be used, as it is 82 * the address range used for I/O (internal registers, 83 * MBus windows). 84 */ 85 reg = <0x00000000 0x00000000 0x00000000 0xf0000000>, 86 <0x00000001 0x00000000 0x00000001 0x00000000>; 87 }; 88 89 cpus { 90 pm_pic { 91 ctrl-gpios = <&gpio0 16 GPIO_ACTIVE_LOW>, 92 <&gpio0 17 GPIO_ACTIVE_LOW>, 93 <&gpio0 18 GPIO_ACTIVE_LOW>; 94 }; 95 }; 96 97 soc { 98 ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000 99 MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000 100 MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000>; 101 102 devbus-bootcs { 103 status = "okay"; 104 105 /* Device Bus parameters are required */ 106 107 /* Read parameters */ 108 devbus,bus-width = <16>; 109 devbus,turn-off-ps = <60000>; 110 devbus,badr-skew-ps = <0>; 111 devbus,acc-first-ps = <124000>; 112 devbus,acc-next-ps = <248000>; 113 devbus,rd-setup-ps = <0>; 114 devbus,rd-hold-ps = <0>; 115 116 /* Write parameters */ 117 devbus,sync-enable = <0>; 118 devbus,wr-high-ps = <60000>; 119 devbus,wr-low-ps = <60000>; 120 devbus,ale-wr-ps = <60000>; 121 122 /* NOR 16 MiB */ 123 nor@0 { 124 compatible = "cfi-flash"; 125 reg = <0 0x1000000>; 126 bank-width = <2>; 127 }; 128 }; 129 130 pcie-controller { 131 status = "okay"; 132 133 /* 134 * The 3 slots are physically present as 135 * standard PCIe slots on the board. 136 */ 137 pcie@1,0 { 138 /* Port 0, Lane 0 */ 139 status = "okay"; 140 }; 141 pcie@9,0 { 142 /* Port 2, Lane 0 */ 143 status = "okay"; 144 }; 145 pcie@10,0 { 146 /* Port 3, Lane 0 */ 147 status = "okay"; 148 }; 149 }; 150 151 internal-regs { 152 serial@12000 { 153 status = "okay"; 154 u-boot,dm-pre-reloc; 155 }; 156 serial@12100 { 157 status = "okay"; 158 }; 159 serial@12200 { 160 status = "okay"; 161 }; 162 serial@12300 { 163 status = "okay"; 164 }; 165 pinctrl { 166 pinctrl-0 = <&pic_pins>; 167 pinctrl-names = "default"; 168 pic_pins: pic-pins-0 { 169 marvell,pins = "mpp16", "mpp17", 170 "mpp18"; 171 marvell,function = "gpio"; 172 }; 173 }; 174 sata@a0000 { 175 nr-ports = <2>; 176 status = "okay"; 177 }; 178 179 mdio { 180 phy0: ethernet-phy@0 { 181 reg = <0>; 182 }; 183 184 phy1: ethernet-phy@1 { 185 reg = <1>; 186 }; 187 188 phy2: ethernet-phy@2 { 189 reg = <2>; 190 }; 191 192 phy3: ethernet-phy@3 { 193 reg = <3>; 194 }; 195 }; 196 197 ethernet@70000 { 198 status = "okay"; 199 phy = <&phy0>; 200 phy-mode = "sgmii"; 201 }; 202 ethernet@74000 { 203 status = "okay"; 204 phy = <&phy1>; 205 phy-mode = "sgmii"; 206 }; 207 ethernet@30000 { 208 status = "okay"; 209 phy = <&phy2>; 210 phy-mode = "sgmii"; 211 }; 212 ethernet@34000 { 213 status = "okay"; 214 phy = <&phy3>; 215 phy-mode = "sgmii"; 216 }; 217 218 /* Front-side USB slot */ 219 usb@50000 { 220 status = "okay"; 221 }; 222 223 /* Back-side USB slot */ 224 usb@51000 { 225 status = "okay"; 226 }; 227 228 spi0: spi@10600 { 229 status = "okay"; 230 231 spi-flash@0 { 232 #address-cells = <1>; 233 #size-cells = <1>; 234 compatible = "n25q128a13", "jedec,spi-nor"; 235 reg = <0>; /* Chip select 0 */ 236 spi-max-frequency = <108000000>; 237 }; 238 }; 239 240 nand@d0000 { 241 status = "okay"; 242 num-cs = <1>; 243 marvell,nand-keep-config; 244 marvell,nand-enable-arbiter; 245 nand-on-flash-bbt; 246 }; 247 }; 248 }; 249 }; 250
